Argo ADG ECO PLUS 100PH Скачать руководство пользователя страница 4

Contents 

1 Safety Notice (Please be sure to abide them) ................. 1 

2 Installation .......................................................................... 5 

2.1 Installation Preparation ..........................................................5 
2.2 Unit Installation .................................................................... 15 
2.3 Electrical Installation ............................................................ 36 
2.4 Check after Installation ......................................................... 47 
2.5 Product Operating Range .................................................... 47 
2.6 Test Running ........................................................................ 47 

3 Product Introduction ....................................................... 49 

3.1 Overall Layout ...................................................................... 49 
3.2 Standard Accessories ........................................................... 50 

4 Installation of Controller ................................................. 51 

5 Maintenance ..................................................................... 52 

5.1 Failures Not Caused by Faults of the AC .............................. 52 
5.2 Error Code ........................................................................... 54 
5.3 Unit Maintenance ................................................................. 57 
5.4 Notice on Maintenance ........................................................ 58 
5.5 After-sales Services ............................................................. 65 

This  marking  indicates  that  this  product should not  be  disposed  with 
other household wastes throughout the EU. To prevent possible harm 
to the environment or human health from uncontrolled waste disposal, 
recycle  it  responsibly  to  promote  the  sustainable  reuse  of  material 

resources. To return your used device, please use the return and collection systems 
or contact the retailer where the product was purchased. They can take this product 
for environmental safe recycling. 

Содержание ADG ECO PLUS 100PH







































































Отзывы: