Arctic Cat F 1100 series страница 42 Скачать руководство пользователя | Manualshive

Страница: 42 / 68

background image

38

Battery (Electric Start)

These sealed batteries after being in ser-

vice require regular cleaning and

recharging in order to deliver peak per-

formance and maximum service life. The

following procedures are recommended

for cleaning and maintaining sealed bat-

teries. Always read and follow instruc-

tions provided with battery chargers and

battery products.



NOTE: Battery maintenance may

be done by the snowmobile owner if
qualified to do so. If the owner does
not feel qualified, take the snowmo-
bile to an authorized Arctic Cat
Snowmobile dealer for this service.
This service is at the discretion and
expense of the snowmobile owner.

To remove and charge the battery, use the

following procedure:

1. Remove the torx-head screw from

the rear underside of the seat; then

remove the seat.

2. Remove the negative battery cable

and ground wire; then remove the

positive cable.



NOTE: For installing purposes

prior to removing the battery, note
the routing and securing locations of
the cables and harness wires.

3. Remove the two screws and lock

nuts securing the battery bracket/

solenoid to the seat-base; then move

the bracket up and out of the way

and remove the battery.

746-170A

4. Thoroughly wash the battery with

soap and water; then using a wire

brush, clean the battery posts and

cable ends removing all corrosive

buildup. Replace damaged cables or

cable ends.



NOTE: If battery posts or cable

ends have a build-up of white/green
powder residue, apply water and
baking soda to neutralize acid; then
flush off with warm soapy water.

5. Using a multimeter, test the battery

voltage. The meter must read no less

than 12.5 DC Volts for a fully

charged battery.



NOTE: At this point if the meter

reads as specified, the battery may
be returned to service (see step 9).

! WARNING

Any time service is performed on a bat-
tery, the following must be observed:
Keep sparks, open flame, cigarettes, or
any other flame away. Always wear
safety glasses. Protect skin and cloth-
ing when handling batteries. When ser-
vicing battery in enclosed space, keep
the area well-ventilated.

! WARNING

Battery posts, terminals, and related
accessories contain lead and lead
compounds, chemicals known to the
state of California to cause cancer
and reproductive harm. Wash hands
after handling.

CAUTION

On the LXR models, make sure to dis-
connect the seat heater harness con-
nector prior to removing the seat.

! WARNING

Avoid spillage and contact with skin,
eyes, and clothing.

CAUTION

Do not charge the battery while it is in
the snowmobile with the battery ter-
minals connected.

CAUTION

Do not remove seal strip on a sealed
battery.

! WARNING

Battery acid is harmful if it contacts
eyes, skin, or clothing. Care must be
taken whenever handling a battery.

«
...
40
41
42
43
44
...
»

Содержание F 1100 series





































































Отзывы:

Нет отзывов

Похожие инструкции для F 1100 series

Бренд: Linn Страницы: 23

Бренд: SMART Devices Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды