79
3. Connect the red MaxiClip to the light green/red wire;
then connect the jumper between the MaxiClips and
turn the ignition switch to the ON position. The neu-
tral indicator light (9) must illuminate.
KM123D
4. Connect the red MaxiClip to the blue/red wire. The
reverse indicator light (10) must illuminate.
5. Connect the red MaxiClip to the white/red wire. The
low range light (3) must illuminate.
6. Connect the red MaxiClip to the green/blue wire.
The temperature indicator (4) must indicate hot (all
indicator segments visible) and begin flashing. The
thermometer icon will also flash.
7. Connect the red MaxiClip to the yellow/white wire.
The fuel quantity indicator (8) must sequence (one
segment every 8-10 seconds) until the bottom seg-
ment begins flashing. After flashing for 8-10 sec-
onds, the bottom segment will extinguish and the gas
pump icon (7) will begin flashing.
NOTE: There must be sufficient gas in the gas tank
to illuminate at least one fuel quantity indicator seg-
ment.
8. Connect the red MaxiClip to the blue wire; then con-
nect a voltmeter to the MaxiClips (red meter lead to
red and black meter lead to black).
9. Set the meter selector to the DC Voltage position;
then turn the ignition switch to the LIGHTS position
and the light control switch to the HI beam position.
The tester must indicate battery voltage and the high
beam indicator light (15) must illuminate. If the tes-
ter does not read battery voltage, troubleshoot the
ignition switch, light control switch, or wiring har-
ness and connectors.
10. Connect the red MaxiClip to the brown/black wire.
The tester must read battery voltage and the speed-
ometer backlight (5) must illuminate. If the tester
does not read battery voltage, troubleshoot the igni-
tion switch or wiring harness connectors.
11. Depress and hold the Mode/Set button (1). The
speedometer should switch between mph and km/h
as indicated by icon (12).
12. Depress and hold the Mode/Set button (2). The dis-
tance mode should shift between ODO and TRIP as
indicated by icon (12).
13. Depress and hold the Mode/Set buttons (1) and (2)
simultaneously. The hour segment of the clock
should flash indicating the clock (13) is in the set
mode. Release the Mode/Set button (2) and release
when the desired hour (1-24) appears.
14. Depress and release the Mode/Set button (1) to shift
the clock set to the minute segment; then depress
Mode/Set button (2) to set the desired minute.
NOTE: In the clock set mode, the gauge will default
to normal operation 10 seconds after the Mode/Set
buttons are released.
15. With the ignition switch in the ON position, use a
small screwdriver or suitable tool to spin the input
quill of the speedometer. The speed indicator (6)
must indicate a value greater than zero.
INSTALLING
To install the LCD gauge assembly, see Steer-
ing/Body/Controls.
CDI Unit
The CDI is located beneath the seat near the battery.
NOTE: The CDI unit is not a serviceable compo-
nent. If the unit is defective, it must be replaced.
The CDI is rarely the cause for electrical problems; how-
ever, if the CDI is suspected, substitute another CDI unit
to verify the suspected one is defective.
NOTE: Prior to replacing the CDI unit to assure the
CDI unit is defective, it is advisable to perform a CDI
peak voltage test and/or perform a continuity test of
the wiring harness from the CDI connector to the CDI
unit.
Содержание Altera 300
Страница 1: ...2017 S SERVICE ERVICE MANUAL ANUAL www arcticcat com ...
Страница 99: ...98 NOTES ...
Страница 100: ...99 NOTES ...
Страница 101: ...100 NOTES ...