Arctic Cat 2010 Crossfire 600 страница 45 Скачать руководство пользователя | Manualshive

Страница: 45 / 60

background image

MAINTENANCE

41

1. Disconnect the taillight harness

connector.

2. Remove

the

two

self-tapping

screws securing the taillight to the
snowflap.

3. Secure the taillight to the snowflap

with the two self-tapping screws;
then connect the taillight connector.

4. Secure the front of the snowflap to

the tunnel by carefully tapping the
snowflap until the two flanged tabs
snap into place.

Removing Headlight

Bulb



NOTE: The bulb portion of head-

light

is

fragile.

HANDLE WITH

CARE. When replacing the head-
light bulb, the bulb assembly must
first be removed from the housing.
Do not touch the glass portion of
the bulb. If the glass is touched, it
must be cleaned with a dry cloth
before installing.

To access the headlight bulbs, use the
following procedure:

1. With the hood closed, loosen the

headlight adjustment knobs.

2. Carefully push the headlight lenses

rearward far enough to remove the
torx-head screws securing the air
silencer plenum to the hood.

3. Open the hood; then remove the

O-rings securing the air silencer
plenum to the hood and remove
the air silencer plenum to access
the bulbs.

4. Remove the bulb from the head-

light housing and disconnect the
wiring harness from the bulb.

0740-462

Installing Headlight

Bulb

1. Plug the wiring harness into the

headlight bulb.

2. Insert the bulb into the headlight

housing.

3. Press the air silencer plenum into

place on the hood and secure with
the O-rings; then close the hood.

4. Carefully push the headlight lenses

rearward far enough to install the
torx-head

screws. Tighten

the

screws securely.

5. Tighten the headlight adjustment

knobs.

6. Check headlight aim (see Adjusting

Headlight Aim in this sub-section).

CAUTION

Do not touch the glass portion of
the bulb. If the glass portion is
touched, it must be cleaned with a
dry cloth before installing.

! WARNING

Do not operate the snowmobile
unless headlight beam is adjusted
properly. An incorrectly adjusted
beam will not provide the operator
the optimum amount of light.

«
...
43
44
45
46
47
...
»

Содержание 2010 Crossfire 600





























































Отзывы:

Нет отзывов

Похожие инструкции для 2010 Crossfire 600

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды