background image

36

MAINTENANCE

1. Loosen the rear idler wheel adjust-

ing bolt jam nuts.

739-636B

2. If the deflection (distance between

the bottom of the wear strip and
the inside of the track) exceeds
specifications, tighten the adjust-
ing bolts to take up excessive slack
in the track.

3. If the distance between the bottom

of the wear strip and the inside sur-
face of the track is less than speci-
fied, loosen the adjusting bolts to
increase the slack in the track.

4. Check track alignment (see Track

Alignment sub-section).

5. When proper track tension is

obtained, tighten the adjusting bolt
jam nuts against the axle housings.

NOTE: Since track tension and

track alignment are interrelated,
always check both even if only one
adjustment seems necessary.

TRACK ALIGNMENT

Proper track alignment is obtained
when the rear idler wheels are equal
distance from the inner track drive
lugs. Excessive wear to the idler
wheels, drive lugs, and track will occur
if the track is improperly aligned. Arc-
tic Cat recommends that the track
alignment be checked once a week or
whenever the track tension is adjusted.

Checking Track 

Alignment

1. Remove excess ice and snow

buildup from the track, track drive
sprockets, and the inside of the
skid frame.

2. Position the tips of the skis against

a wall; then using a shielded safety
stand, raise the rear of the snow-
mobile off the floor making sure
the track is free to rotate.

3. Start the engine and accelerate

slightly. Use only enough throttle
to turn the track several revolu-
tions. SHUT ENGINE OFF.

! WARNING

If jam nuts are not tightened prop-
erly, the adjusting bolts could
loosen

causing

the

track

to

become

extremely

loose

and,

under some operating conditions,
allow the idler wheels to climb over
the track lugs forcing the track
against the tunnel causing the
track to “lock.” If a track “locks”
during operation, severe personal
injury could result.

! WARNING

Make sure the ignition key is in the
OFF position and the track is not
rotating before checking or adjust-
ing

track

alignment.

Personal

injury could result if contact is
made with a rotating track.

! WARNING

The tips of the skis must be posi-

tioned against a wall or similar
object.

! WARNING

DO NOT stand behind the snowmo-
bile or near the rotating track.
NEVER run the track at high speed
when the track is suspended.

Содержание 2010 Crossfire 600





























































Отзывы:

Похожие инструкции для 2010 Crossfire 600