Arconic DT4600 Скачать руководство пользователя страница 11

Страница: 11 / 14

DT4600 Pneudraulic Installation Tool (HK1174)

Components Drawing 2 of 3 -

Section A-A from Figure X

130427 Connecting Tube

503965 O-ring

500809 O-ring

505841 Polyseal

500786 O-ring

130411 Hydraulic

Cylinder

130415 Handle Assembly

130417 Air

Cylinder Assembly

130418 Hydraulic Piston Assembly

2-part Piston Rod not sold separately

500817 O-ring

500789 O-ring

130608 GLYD Ring

130439 Retaining Nut

130420 Trigger

502571

O-ring

500774

O-ring

130426 Trigger

Valve Body

508538

O-ring

130443 Trigger

Valve Spool

502571

O-ring

130425

Trigger

Button

Detail of 130446

Trigger Valve Assy

130424 Nose Adapter

Apply Loctite® 243™ Threadlocker

to threads and torque to 50 ft/lbs.

124211 Pintail

Deflector

130440

Vacuum

Shut-off

130451 Hydraulic End

Cap Assembly

(End Cap

not sold separately)

500780 O-ring

Apply Loctite® 243™

Threadlocker to threads

and torque to 50-60 ft/lbs.

500778 O-ring

500792 O-ring

130430

Retaining Nut

Apply Never-Seez® to

threads and torque to 15 ft/lbs.

130444 Piston Rod

Apply Loctite® 243™

Threadlocker to threads.

508542 O-ring

130432 Air Piston

500908 O-ring

508953 O-ring

130422 Bottom End Cap

130421 Ring Bumper

505827 Polyseal

130450 Front Gland Assembly

Front Gland not sold separately

504034 O-ring

505817

Wiper

Torque to 10-15 ft./lbs.

500619 Slotted Pin

Apply Loctite® 243™

Threadlocker to threads.

DT4600_revD

Figure 7

Содержание DT4600















Результаты поиска

Содержание DT4600

Отзывы:

Похожие инструкции для DT4600

Бренды по названию

Популярные бренды

Arconic DT4600, Инструкция по эксплуатации

Результаты поиска

Содержание DT4600

Отзывы:

Похожие инструкции для DT4600

Бренды по названию

Популярные бренды