Arconic 2022 Series страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 20

background image

15

2022 and ERT9 series Pneudraulic Installation Tools (HK1021)

Tool Base Components (All Models)

130729

500903

Bottom Plate

**

** When replacing the Cylinder Assembly,

these stickers MUST be ordered and placed

as shown

.

Detail of sticker locations

Note orientation.

Tighten and torque to 36–66 ft.-lbs.

NOTES

:

Cylinder Head Assembly

123778-1

:

---- Cylinder Head (not sold separately)

500864 O-ring

Throttle Valve Assembly

125472-2

:

---- Throttle Valve (not sold separately)

507396 O-ring (qty. 3)

Cylinder Assembly

125733

includes:

---- Cylinder (not sold separately)

505496 Dowel Pin

500782 O-ring

125466 Upper Bushing

115503 Lower Bushing

Figure 14

«
...
13
14
15
16
17
...
»

Содержание 2022 Series





















Отзывы:

Нет отзывов

Похожие инструкции для 2022 Series

Бренд: ICP Страницы: 38

Бренд: jbc Страницы: 12

Бренд: jbc Страницы: 8

Бренд: Samoa Страницы: 16

Aquajoe FIBERJACKET AJFJH50-58-PRO-RM

Бренд: SNOWJOE Страницы: 8

Бренд: Sammic Страницы: 2

Бренд: SATA Страницы: 16

sunjoe24V-HG100

Бренд: SNOWJOE Страницы: 52

Бренд: BGS technic Страницы: 4

Бренд: JAE Страницы: 10

Бренд: JCM GLOBAL Страницы: 32

Бренд: Gern Pro Страницы: 25

Бренд: SATA Страницы: 74

Бренд: Stanley Страницы: 12

Бренд: Reliable Equipment Страницы: 22

Бренд: Kaindl Страницы: 19

Бренд: Yokota Страницы: 8

Бренд: Baileigh Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды