background image

3.0 Inspection, Maintenance and Storage

3.1 Record Keeping

All components should be checked daily when used regularly. Regardless of the usage, each

respirator system requires a documented inspection and replacement program. A trained and 

competent person with full knowledge of respiratory equipment should carry this out. Records

should be maintained throughout the life of the equipment. Regulatory Guidance can be found

in the following documents: OSHA 29CFR 1910 Part 134 and ANSI Z88.2. 
Use only 

A

RC

O

NE

®

A

IR

P

LUS

®

PAPR

components and replacement parts manufactured by 

A

RC

O

NE

®

and approved by NIOSH for use with the respirator system. Inspect all components of

the respirator system during cleaning, and before and after each use for signs of wear, tear or

damage that might reduce the degree of protection originally provided. Respirators used by

more than one person must be cleaned, inspected, and sanitized after each use. If not cleaned,

contamination may cause illness or disease. Allow components to air dry before reassembling. 

3.2 Cleaning 

1. ALWAYS INSPECT your 

A

RC

O

NE

®

A

IR

P

LUS

®

PAPR

system before each use and after

cleaning. Clean the external surfaces of the PAPR system with a soft cloth dampened in a

mild solution of clean water and mild detergent. Never use abrasive cleaners. During

cleaning, ensure that NO water is allowed to enter into the blower unit or battery pack as this

could damage the blower or battery internal parts. Never immerse the unit in liquid.

2. Detach the Breathing Tube from the Blower unit and the Headtop (Section 4.4), and wipe

the connection sites.

3. Detach the Face Seal from the Headtop before cleaning (Section 4.5). Hand wash in a mild

solution of clean water and mild detergent. Air dry the Face Seal then re-apply a fire retardant

spray (Fig. 16) and allow the Face Seal to air dry before reattaching to the Headtop.

4. Allow all components to dry away from direct heat.

5. Refer to the 

A

RC

O

NE

®

Auto-Darkening Filters manual for maintenance of applicable

components.

®

-15-

Figure 16

Содержание AIRPLUS

























Отзывы: