manualshive.com logo in svg

ARCBRO Stinger Series, Руководство пользователя, Страница: 57 / 77

Поделиться
Скачать
ARCBRO Stinger Series Скачать руководство пользователя страница 57

Service Support Spirit                 

 

 

 

Unique Solution                                    

  WWW.ARCBRO.COM

 

 

57 

IGNITION——It is the time delay when turn on the high voltage ignition switch if M20 is executed in flame 
cutting operation. 

HOTUP TIME——It is the preheating time for piercing operation in second. If the preheating time is 
insufficient, it will be prolonged to 150 seconds automatically by pressing [PAUSE] key. If preheating is done 
in the midway, Press [START] key to abort the time delay. The new preheating time will be automatically 
saved in the parameter of preheating delay.   

TORCHUP TIME(M70)——Torch rising time The time delay when M70 command is executed in second. 
Refer to 6.4 for M auxiliary commands.   

TORCHDN TIME(M71)——Torch down time, The time delay when M71 command is executed, in 
second. Refer to 6.4 for M auxiliary commands.   

PIERCEUP HIGH(M72)——Torch  rising time after pierce  The time delay when M72 command is 
executed, in second. Refer to 6.4 for M auxiliary commands.   

PIERCEDN HIGH(M73)——Torch falling time after pierce  The time delay when M73 command is 
executed, in second. Refer to 6.4 for M auxiliary commands.   

PIERCE TIME——Lowering delay of cutting torch when M07 is executed in flame piercing 
operation after cutting oxygen valve is opened.   

OVER CUT DELAY-TIME----

 

Automatically disconnect oxygen delay;

 

After turning off the cutting 

oxygen, due to the residual pressure in the tube, after this delay, proceed to the next step to 
improve the cutting surface finish. 

LINE DELAY-TIME--- After the program line is in place, after this delay time, run the next line 
Move to the next piercing point after completing a cut. 

SELECT HI HOTUP M24 (0/1)---

 

When the thick plate is perforated, the high preheating aid is 

required. When this function is selected, M24 is turned on during preheating, and M24 is closed 
after preheating. Note: When this option is not selected, M24 (preheating) will not be turned off 
during the entire processing.

 

1 is to choose, 0 is not to choose; 

GAS ON M ORDER---

 

Open the  output port address used by the gas solenoid valve (see 

diagnosis function), 

Содержание Stinger Series














































































Отзывы:

Нет отзывов