Arc Machines M96 Скачать руководство пользователя

Страница: 21 / 22

Doc No. 740048

MODEL 96

TUBE TO TUBESHEET WELD HEAD

OPERATION MANUAL

13.0 Available Options

Description

Part Number

Gas Chambers

Gas Chamber (clear)

42900703-01

Electrode holders

Electrode Holder, 0.040” (1mm)

42960700-04

Electrode Holder, 3/32” (2.4mm)

42960703-01

for tubes over 2.00” (50.8mm) O.D.

I.D. Mandrels
0.37” – 0.40” I.D. (9.4 - 10.2mm)

13961004-02

0.40” - 0.44” I.D. (10.2 – 11.2mm)

13961004-31

0.42” – 0.46” I.D. (10.7 – 11.7mm)

13961004-10

0.47” – 0.52” I.D. (12.0 – 13.2mm)

13961004-39

0.48” - 0.53” I.D. (12.2 – 13.5mm)

13961000-03

0.53” – 0.60” I.D. (13.5 – 15.3mm)

13961000-08

0.61” - 0.66” I.D. (15.5 – 16.8mm)

13961000-05

0.64” – 0.70” I.D. (16.3 – 17.8mm)

13961000-04

0.68” – 0.74” I.D. (17.3 – 18.8mm)

13961000-06

0.74” – 0.80” I.D. (18.8 – 20.3mm)

13961000-09

0.80” – 0.84” I.D. (20.3 – 21.3mm)

13961001-08

0.83” – 0.88” I.D. (21.1 – 22.4mm)

13961001-02

0.88” – 0.93” I.D. (22.4 – 23.6mm)

13961001-01

0.92” – 0.97” I.D. (23.4 – 24.6mm)

13961001-14

0.93” – 0.98” I.D. (23.6 – 24.9mm)

13961001-11

0.97” - 1.02” I.D. (24.6 – 25.9mm)

13961001-03

1.04” – 1.09” I.D. (26.4 – 27.7mm)

13961001-09

1.10” – 1.15” I.D. (27.9 – 29.2mm)

13961001-04

1.19” – 1.21” I.D. (30.3 – 30.7mm)

13961001-13

1.34” – 1.39” I.D. (34.0 – 35.3mm)

13961001-05

1.40” – 1.45” I.D. (35.5 – 36.7mm)

13961001-38

1.43” – 1.48” I.D. (36.4 – 37.5mm)

13961001-35

1.52” – 1.57” I.D. (38.6 – 39.8mm)

13961001-37

1.55” – 1.60” I.D. (39.4 – 40.6mm)

13961001-12

1.60” – 1.65” I.D. (40.6 – 42.0mm)

13961001-06

1.76” – 1.81” I.D. (44.7 – 46.0mm)

13961001-36

1.85” – 1.90” I.D. (47.0 – 48.3mm)

13961001-07

1.92” – 1.97” I.D. (48.7 – 50.0mm)

13961001-10

1.97” – 2.03” I.D. (50.0 – 51.6mm)

13961001-39

Содержание M96























Результаты поиска

Содержание M96

Отзывы:

Похожие инструкции для M96

Бренды по названию

Популярные бренды

Arc Machines M96, Руководство по эксплуатации

Результаты поиска

Содержание M96

Отзывы:

Похожие инструкции для M96

Бренды по названию

Популярные бренды