Aqua Lung SEA LV2 Скачать руководство пользователя страница 13

Страница: 13 / 32

NOTE: Before continuing, closely examine the back-up

ring (24). You will note that it has a flat side and a concave

side. For correct assembly, the concave side should be

against the o-ring (25), as shown in the picture.

O-ring

Back-up ring

17.

Using the squared end of the stem (28), screw the seat

disc & retainer (29) into the port on the first stage body (8).

Leave the stem in position, place the handwheel (18) over

the stem and tighten the seat disc & retainer until finger tight.

Remove the handwheel from the stem.

18.

Install o-ring (23) onto the bonnet (21) so that the o-ring

fits into the groove located above the threads. Lubricate the

bonnet threads, then pass the bonnet over the stem and

thread it into the first stage body (8) until hand-tight.

19.

Use a 3/4” socket and

inch pound torque wrench

to apply 90 in-lbs (10.2 Nm)

of torque to the bonnet (21).

20.

Place the nylon washer

(19) over the stem (28), so it

sits on top of the bonnet (21).

Face the round edge on the

indicator ring (20) outward and

thread the indicator ring onto

the bonnet until it bottoms out.

21.

When the indicator ring

(20) bottoms out, turn it

slightly counter-clockwise

so the square corners on

the stem (28) shaft are

aligned with the square

cutouts on the indicator

ring. Turn an additional 90°

counter-clockwise.

22.

Place the handwheel (18) over the indicator ring (20). Place

the spring (17) into the handwheel, followed by the washer (16).

Using the modified screwdriver, screw the handwheel retainer

(15) onto the end of the stem (28) until it will not turn any further.

CAUTION:

If resistance is felt while screwing the

handwheel retainer (15) onto the stem (28), stop

and start over to avoid cross threading.

23.

Install o-ring (12) onto the

threaded end and o-rings (13)

into the grooves on the swivel

port plug (14).

16.

In the following order,

place a new Teflon washer

(27), brass washer (26),

o-ring (25) and back-up ring

(24) onto the stem (28).

Reassembly of Handwheel

NOTE: DO NOT apply any type of lubricant to the seat

& disc retainer (29) prior to installation.

Содержание SEA LV2

































Результаты поиска

Содержание SEA LV2

Отзывы:

Бренды по названию

Популярные бренды

Aqua Lung SEA LV2, Техническое руководство

Результаты поиска

Содержание SEA LV2

Отзывы:

Бренды по названию

Популярные бренды