Aqua Lung SEA LV2 Скачать руководство пользователя страница 10

Страница: 10 / 32

SEA MK / LV2 Technical Manual

Place the threaded end of the poppet (56) directly over

the poppet bearing (58) and press down to dislodge it from

the valve body (59).

Using the SS o-ring tool

(PN 10 -102- 400) pierce

the middle of the MP seat

(55) and remove it from the

poppet (56).

NOTE: DO NOT discard used MP seat (55), it will be

used to aid in the reassembly process.

NOTE: Before beginning reassembly,

perform parts cleaning and lubrication in

accordance with Procedure A: Cleaning

and Lubricating.

REASSEMBLY PROCEDURE

CAUTION:

Before proceeding, visually inspect the

cylinder according to Compressed Gas Associa-

tion (CGA) standards pamphlet (CGA C 6.1: 2013,

STANDARD FOR VISUAL INSPECTION OF HIGH

PRESSURE ALUMINUM ALLOY COMPRESSED

GAS CYLINDERS). This inspection requires a visual

inspection light. If the cylinder does not pass the

visual inspection, it must be serviced or replaced

with a new cylinder before it can be assembled

and filled.

NOTE: Before performing any reassembly, it is

important to inspect all parts, both new and those

that are being reused, to ensure that every part

and component is perfectly clean and free of any

dust, corrosion or blemishes. Before dressing

each o-ring with Christo-Lube

, check to ensure it

is clean, supple and free of any blemishes.

WARNING:

Use only genuine Aqua Lung

parts, sub-assemblies and components when-

ever assembling any Aqua Lung

product. DO

NOT attempt to substitute an Aqua Lung

part

with another manufacturer’s, regardless of any

similarity in shape, size or appearance. Doing

so may render the product unsafe and could

result in serious injury or death.

Install o-ring (30) over the

threads on the first stage

body (8). Lubricate the first 4

to 5 threads on the first stage

body with Christo-lube®.

Thread the first stage body

(8) into the cylinder (43) until

hand-tight. Secure the strap

wrench to the cylinder. Use

a 1 3/16” crowfoot and foot

pound torque wrench to apply

25 ft-lbs (33.9 Nm) of torque to

the first stage body.

CAUTION:

Ensure that the crowfoot is aligned with the

wrench flats on the first stage body (8). Do not position

the crowfoot over the bonnet opening as this will cause

damage, resulting in replacement of the first stage body.

NOTE: Another option is to use vise jaw inserts (PN

100398) in conjunction with a bench vise to install the

first stage body (8) onto the cylinder (43).

Valve Body Disassembly

CAUTION:

The valve body assembly is under spring

tension, use caution during disassembly.

Using a 1/4" nut driver, remove the locknut (62) from the

poppet (56). Remove the washer (61), lever (60), spring (57)

and poppet (56) from the valve body (59).

Remove the o-ring (23)

from the inlet fitting (51).

First Stage Reassembly

Содержание SEA LV2

































Результаты поиска

Содержание SEA LV2

Отзывы:

Бренды по названию

Популярные бренды

Aqua Lung SEA LV2, Техническое руководство

Результаты поиска

Содержание SEA LV2

Отзывы:

Бренды по названию

Популярные бренды