APT 310XAC Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 146

background image

68

can press the Prev or Next soft key.

4.6.7 Editing Transient * (PROGRAM Mode only)

Use the

∧

,

∨

soft keys to navigate to the Transient parameter (only selectable for

AC output). Pressing the Edit soft key will provide the following screens:

Transient = indicates the Transient mode that is programmed into the instrument.

Transient Mode: indicates the Transient mode that can be programmed into the
instrument.

The Transient modes available are ON and OFF. Press the Change soft key to
toggle the mode to ON or OFF. To save the parameter, press the Enter soft key.
To cancel the editing of the Transient mode press, the Esc soft key. When the
Enter soft key is pressed the Transient mode is accepted and you transition into
the next parameter: Trans-Volt*.

If you wish to bypass editing this parameter and move to the next parameter you
can press the Prev or Next soft key.

*If the Transient parameter is turned ON additional parameters of Trans-Volt,
Trans-Site, Trans-Time, and Trans-Cycle will be present in the Test Parameters
screen.

4.6.8 Editing Trans-Volt* (PROGRAM Mode only)

Use the

∧

,

∨

soft keys to navigate to the Trans-Volt parameter (only selectable for

AC output). Pressing the Edit soft key will provide the following screen:

«
...
66
67
68
69
70
...
»

Содержание 310XAC



















































































































































Отзывы:

Нет отзывов

Похожие инструкции для 310XAC

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Keithley Страницы: 171

Бренд: Furman Страницы: 28

Бренд: AudioQuest Страницы: 2

Бренд: Adam Hall Страницы: 2

Бренд: LEGRAND Страницы: 50

Pow-R-Line P2R Series

Бренд: Eaton Страницы: 14

Бренд: Abtus Страницы: 2

HighPROtec MCDLV4

Бренд: Woodward Страницы: 1275

Бренд: Tripp Lite Страницы: 3

Бренд: Tripp Lite Страницы: 4

Perfect Wave Transport

Бренд: PS Audio Страницы: 1

Бренд: PS Audio Страницы: 8

PerfectWave Power Plant 5

Бренд: PS Audio Страницы: 18

Бренд: PS Audio Страницы: 32

PowerPlay IPC-8000

Бренд: PS Audio Страницы: 47

Бренд: Mastervolt Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды