manualshive.com logo in svg

APS Resource HTC Kit, Инструкция по установке и эксплуатации

Поделиться
Скачать
APS Resource HTC Kit Скачать руководство пользователя страница 6

PAGE 5

©2010 4Front Engineered Solutions, Inc. - APS Resource 

    

             

AP4047 RA 11/10

               

INsTALLATION

Be sure to safely secure ramp with proper hoists 

and safety struts before doing any work under the 

leveler.  Failure to do so could allow the ramp to fall, 

resulting in serious injury or death. 

sITE PREPARATION

Place barricades around pit on dock floor and driveway 

before installing, maintaining, or repairing dock leveler.

1.   In this conversion you will be removing the ramp’s 

lifting mechanism. After the ramp has  been opened 

into the “up” position, it must be safely secured with 

the proper hoists and safety struts before work can 

begin. Failure to do so could allow the ramp to fall 

resulting in serious injury or death.

2.   Mount and wire push-button station (See Figure 1) 

and pit mounted receptacle (See Figure 2).  See 

wiring diagram located on the inside cover of the 

control box or wiring diagrams in this manual for 

wiring information.  Follow the wiring instructions 

to set control for proper voltage.  Wires show in 

dashed lines are field connections.

3.  If conduit must be installed do so at this time.  Refer 

to the conduit requirements on the pit detail (See 

Figure 2).  Follow all applicable electrical codes and 

standards.

Push-button

control station

48"

Figure 1

Figure 2

Содержание HTC Kit





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды