APS Resource HTC Kit Скачать руководство пользователя страница 20

Страница: 20 / 28

PAGE 19

AP4047 RA 11/10

OPERATION

Before allowing vehicle to leave always return the dock

leveler to its dock level (stored) position with the dock

level support legs supported by the front dock level

supports. Failure to do so may leave the dock leveler

in a position below the level of the dock floor. This

condition may result in unexpected drop of personnel

or material handling equipment and result in death or

serious injury.

7. To return the dock leveler to the stored position when

loading or unloading is complete.

7.1 Turn the “ON/OFF” switch to the “ON” position.
7.2 Push and hold the “RAISE” button. The ramp will

rise and the lip will lower.

7.3 Release the "RAISE" button when the lip is fully

retracted. The ramp will lower to the dock level

(stored) position.

7.4 Check that the lip is not extended and the ramp

is supported by both dock level supports before

driving or walking on the ramp. Ramp should be

level with dock floor.

7.5 Turn the “ON/OFF” switch to the “OFF” position.

8. Unchock or release vehicle.
9. Tell vehicle driver “Your vehicle may now leave the

dock.”

BELOW DOCK END LOADING

To lower the ramp without extending the lip for end loading

below dock level:

1. Turn the “ON/OFF” switch to the “ON” position.
2. Press the "RAISE" button and hold it until leveler is

fully raised and the lip starts to extend. When the lip

has extended 2 to 3 inches to clear the front of the lip

keepers, release the button.

3. Turn the “ON/OFF” switch to the “OFF” position as the

ramp begins to lower. Leveler will float down for end

4. Load or unload end loads.
5. When loading or unloading is complete, return the

dock leveler to the stored position. Turn the “ON/

OFF” switch to the “ON” position. The dock leveler will

automatically return to the stored position.

6. Visually check that the lip is not extended and the

ramp is supported by both dock level supports before

driving or walking on the ramp. Ramp should be level

with dock floor.

7.  Turn the “ON/OFF” switch to the “OFF” position.
8.  Unchock or release vehicle.
9.  Tell  vehicle  driver  “Your  vehicle  may  now  leave  the

dock”.

AuTO RETuRN TO DOCK (A.R.T.D.)

OPERATION

The A.R.T.D. automatically resets the leveler whenever a

vehicle just pulls away from the loading dock with the lip

resting on the vehicle. This is how it works.

1. If the vehicle pulls away, the leveler will float down to

the lowest position and the lip will fall. The leveler will

automatically raise, retract the lip, then float down to

the stored position.

Figure 32

Содержание HTC Kit





























Результаты поиска

Содержание HTC Kit

Отзывы:

Бренды по названию

Популярные бренды

APS Resource HTC Kit, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HTC Kit

Отзывы:

Бренды по названию

Популярные бренды