APRILIA RSV 1000 R Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 308

APRILIA RSV 1000 R Скачать руководство пользователя страница 91

FUEL SYSTEM

3 - 24

RSV

1000

R - RSV

1000

R FACTORY

3.3.4.

REFITTING THE THROTTLE BODY

CAUTION
After disassembling the throttle body, replace
all the gaskets, O-rings, torsion springs,
bushes and seals. These components are sup-
plied with the repair kit.

•

Fit the new O-rings (1) and seals (2) on both injectors.

•

Insert the injector (3) in the left injector support (4) and
in the right injector support (5).

•

Fit the left injector support gasket (6), right injector
support gasket (7) and the two seals (8) on the throttle
body.

•

Install the complete left injector support (4) and right in-
jector support (5) in the throttle body, fastening them
with the new M6x25 (9) (10) screws respectively.

•

If the synchronizing screws (11) and respective O-rings
(12) have been replaced, tighten the screws (11) until
they touch the stop and then unscrew them a single
turn.

Presetting of synchronizing screws (11): 1 turn.

CAUTION
The precise adjustment of the screws (11) must
be performed using a vacuum gauge.

•

Fasten the fuel pressure regulator (13) using the two
M6x16 screws (14).

NOTE

Smear a film of grease over the surfaces of the ful-

crum pin (18).

•

Insert the cold-start lever (15), torsion spring (16) and
shaft-sealing ring (17) on the fulcrum pin (18).

•

Insert the complete fulcrum pin (18) in the throttle ca-
ble support bracket.

NOTE

Make sure the torsion spring is hooked to the cold-

start lever (15) and the cable support bracket.

•

Spray chain grease on the spring (16).

•

Insert the shaft-sealing ring (17) on the fulcrum pin
(18).

•

Fit the two bushes (19) and torsion spring (20).

•

Fit the pulley (21) on the throttle cable support bracket.

«
...
89
90
91
92
93
...
»

Содержание RSV 1000 R





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды