manualshive.com logo in svg

APRILIA RSV 1000 R, Руководство по ремонту

Поделиться
Скачать
APRILIA RSV 1000 R Скачать руководство пользователя страница 270

 

 

CYCLE PARTS

5 - 125

RSV 

1000

 R - RSV 

1000

R FACTORY 

 

WARNING 
The four brake pads must always be replaced to-
gether. Ensure they become properly seated in the 
brake caliper.

 

 

• 

Position the retaining clip (2). 

• 

Press the retaining clip (2) and insert the pin (3) from the 
inside. 

• 

Release the retaining clip (2) and ensure it becomes 
securely engaged with the pin (3). 

 

 

DANGER 
When released, the retaining clip (2) should become 
correctly located into its seats to lock the pin (3) in 
place. 
When the clip is positioned correctly, the pin (3) will 
not come off. Try to extract the pin to ensure clip 
and pin are securely in place.

 

 
 

 

 

• 

Position the front brake caliper on the brake disc. 

• 

Tighten the two bolts (1) fully until finger tight. 

• 

Operate the front brake lever. This will help the brake caliper 
become properly seated. 

• 

Keep the brake squeezed in and tighten the two bolts (1). 

• 

Check the front brake fluid level. 

 

 

 

Содержание RSV 1000 R





















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды