manualshive.com logo in svg

Approach Engineering AH-64A Apache-50, Инструкция по эксплуатации

Поделиться
Скачать
Approach Engineering AH-64A Apache-50 Скачать руководство пользователя страница 23

APACHE 50                      PAGE #  23 

                                                                                         Dawson’s 

APPROACH E GI EERI G  

                                                                                                                         AH-64A  50  MECHA ICS 

15.7  

Punch out the 1/8” plywood horizontal fin control horn 

HCH.  Viewing from the bottom glue the control horn against 
the side of the fin support and the lip of the center sheeting.  

15.8  

Pull out the two pieces of  ½” leading edge stock 5 and 

3/8” in length.  Glue the leading edge stock centered on the 
leading edge with CA+.  After finished sand the leading edge to 
a rounded finished shape.  

15.9  

Viewing the horizontal fin from the bottom punch out the 

1/16” balsa horizontal fin center, HFC.  This will fit in the cen-
ter trailing edge of the fin.  Note:  The HFC will be installed at a 
angle therefore it is recommended to sand the upper and lower 
sheet surfaces at the same angle to create a flat surface for the 
HFC to be glued.  When satisfied glue the HFC in place and 
sand the edges flush with the upper and lower sheeting.  

15.10  

Working on the horizontal fin tips, punch out the two 

¼” balsa pieces HFT.  Glue on the fin tips making sure they are 
centered on wing tip.  Note, the horizontal fin tips are purposely 
made larger to allow for sanding flush with the surfaces.  When 
complete sand the upper and lower surfaces flush with the 
sheeting and leading edge. 

 

15.11  

Sand the horizontal fin tips to a rounded finished shape 

using the pictures as a guide. 

 

15.12  

Pull out the two 9/32” by ¼” brass tubes.  Punch out the 

two lower horizontal fin supports HFS-2 from the ¼” light ply 
sheet.  Roughen up the outside surface of the brass tubes with 
sandpaper.  Glue the brass tubes into the half circle in the lower 
fin supports.  Put into place and drill and countersink the holes.  
Temporarily install the screws to check the fit. 

 

15.0  HORIZO TAL FI  
         ASSEMBLY 

Содержание AH-64A Apache-50















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды