manualshive.com logo in svg

Applied Instruments NPRT 2200, Руководство по эксплуатации

Поделиться
Скачать
Applied Instruments NPRT 2200 Скачать руководство пользователя страница 6

Operation Manual

NPRT 2200

3. Front Panel Operations

The NPRT 2200 stand-alone operations are limited to single point NPR testing, source controls, 
calibration and diagnostics. Stand-alone power sweep tests may be available in a future version.  
Power Sweep tests are available with this version using the supplied PC software.

The manual control screen lets you select which frequency range, and notch filter to use, if more 
than one are provided.  It also lets you switch the notch in and out and set any desired output 
power level.  Finally, it displays the measured input power.

In a single point manual NPR test, you enter the desired power level and the instrument 
measures and displays the corresponding Noise Power Ratio.

3.1.

Main Menu

The first screen shown after power-up is the main menu.  There are two main menu screens:

  

Press MORE to display the second menu screen:

The menu options are:

1) NPR – make NPR measurements at a selected power levels
2) Manual – Set source output controls and measure received power
3) Cal – Cable calibration procedure
4) Setup – change screen contrast and options
5) Diag – diagnostic screens

You may select an option by pressing the “soft key” directly under the menu option.

Page 4

Main Menu

                 
          
    NPR     Manual     Cal    MORE

Main Menu

                 
          
    Setup    Diag             MORE

Содержание NPRT 2200






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды