Applied Instruments NPRT 2200 Скачать руководство пользователя страница 26

Страница: 26 / 29

Operation Manual

NPRT 2200

Turns user calibration on or off.

Selecting Units

UNIT:POWer <units>
UNIT:POWer?

Specifies the desired units for the power readings. The possible values are:
dBm (default)
dBmV
dBuV
dBmV / Hz
dBuV / Hz

Releasing the Port

SYSTem:RELease

This command will release the locked port allowing either port access with the next command.

SYSTem:RELease:TIMEout <seconds>

This command will set a timeout for automatic release of the port if no further commands are
received with the given number of seconds. A default value of 60 seconds is set upon power up.

See Section 6.6 for more information on these commands.

6.3.

Error Reporting

The system error query command is supported for a few types of errors:

SYSTem:ERRor?

Returns one of the following:

0, "No error"
-100, "Command error"
-350, "Queue overflow"

6.4.

SCPI Required Commands

The following commands are implemented as required by the SCPI standard but have no real
function in the NPRT 2200.

*CLS

Clear Status Command

*ESE

Standard Event Status Enable Command

*ESE?

Standard Event Status Enable Query

*ESR?

Standard Event Status Register Query

*IDN?

Identification Query

*OPC

Operation Complete Command

*OPC?

Operation Complete Query

*RST

Reset Command

*SRE

Service Request Enable Command

*SRE?

Service Request Enable Query

*STB?

Read Status Byte Query

Page 24

Содержание NPRT 2200






























Результаты поиска

Содержание NPRT 2200

Отзывы:

Похожие инструкции для NPRT 2200

Бренды по названию

Популярные бренды

Applied Instruments NPRT 2200, Руководство по эксплуатации

Результаты поиска

Содержание NPRT 2200

Отзывы:

Похожие инструкции для NPRT 2200

Бренды по названию

Популярные бренды