manualshive.com logo in svg

Applied Instruments NPRT 2200, Руководство по эксплуатации, Страница: 25 / 29

Поделиться
Скачать
Applied Instruments NPRT 2200 Скачать руководство пользователя страница 25

Operation Manual

NPRT 2200

Measuring Level

MEASure:LEVel?

Measures the received power level at the presently selected range, notch and source power 
level.

Measuring Carrier Level

MEASure:CARrier?

Removes the notch filter and measures the resulting carrier power level at the present source 
power settings.

Measuring Noise

MEASure:NOISe?

Measures the noise level within the notch at the presently selected range, notch and source 
power level.

Fetching Associated Readings

After executing an NPR measurement, you can also fetch the associated carrier level and noise 
level readings used in that NPR measurement with the following commands:

FETCh:CARrier?
FETCh:NOISe?
FETCh:NPR?
FETCh:[SOURce:]POWer[:LEVel]?

If the associated value is not valid an error –230 is posted.  This is usually caused by an 
unrelated measurement being performed after the last instance of the desired parameter was 
taken.  For instance: if a MEAS:NPR? is executed, all parameters are valid, then if a 
MEAS:NOISE? is executed, the carrier and NPR values are no longer valid because they are not 
measured by the MEAS:NOISE function.

Changing Averaging Setup

[SENSe:]AVERage[:COUNt]  <value>
[SENSe:]AVERage[:COUNt]?

Set the averaging count

Changing Settling Time

 [SENSe:]SETTle  <milli-seconds>
[SENSe:]SETTle?

Sets the settling time between changing the power and taking a reading.  The default is 500 
mSecs.

Turning Temperature Compensation On/Off

CAL:COMP:TEMP <Boolean>

Turns temperature compensation on or off.

Turning User Calibration Compensation On/Off

CAL:COMP:USER <Boolean>

Page 23

Содержание NPRT 2200






























Отзывы:

Нет отзывов