Appliance Desk 4000 Скачать руководство пользователя | Manualshive

Страница: 5 / 33

background image

~ 4 ~

IMPORTANT PRESERVICE INSTRUCTIONS

►

It is advisable for anyone to go through the following points before one actually works on the unit.

•

Shipping Rods

:

The unit is shipped with 2 shipping rods and spacers to avoid any damage to the

unit during shipping. Make sure that all the shipping rods and the spacers have been removed from the

unit.

•

Height of drain hose

:

The drain hose should be placed in such a way that the height of the drain

hose does not exceed 36” and is not lower than 28” inches from the bottom of the unit.

•

Water inlets

:

In this unit two water inlets are required to be connected for hot as well as for cold

water(Note that Valves are Matrix Size & L Connector of the inlet hose supplied with the machine is also

Matrix. The straight connector is US Thread). Make sure that water supply is provided to both the inlets. In

case hot water supply is not available cold water supply should be connected to the hot water inlet valve.

•

Leveling

:

The unit must be leveled properly for proper working of the unit. There are 4 leveling feet

which can be individually leveled.

•

Flooring

:

The unit should be installed on strong and leveled floor, installation on carpet or wood

increases vibrations. In case of wooden flooring, proper bracings should be made and the unit should be

installed on a sheet of plywood.

※

Please note:

All the above instructions are mentioned in the Owner’s Manual

and if the unit is found to be malfunctioning due to any of the above points not
been taken care of, the customer will be liable to pay for the complete service
call along with the parts. If the customer is not willing to pay for the service we
will be paying for the same but the customers warranty will be voided then.

«
...
3
4
5
6
7
...
»

Содержание 4000


































Отзывы:

Нет отзывов

Похожие инструкции для 4000

Бренд: Lavor Страницы: 20

Бренд: Indesit Страницы: 72

Бренд: Michelin Страницы: 40

Бренд: Mancorp Страницы: 13

AQUALTIS AQLF8F 292 U

Бренд: Hotpoint Ariston Страницы: 64

Бренд: Wen Страницы: 23

Бренд: Spitwater Страницы: 23

Бренд: CDA Страницы: 40

Бренд: Asko Страницы: 2

Бренд: Splendide Страницы: 2

Бренд: Artusi Страницы: 36

Бренд: Iberna Страницы: 24

Бренд: Maytag Страницы: 36

Бренд: Hotpoint Страницы: 16

Бренд: Simoniz Страницы: 10

Бренд: Indesit Страницы: 72

Бренд: Danby Страницы: 44

Бренд: Parker Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды