Appliance Desk 4000 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 33

background image

~ 19 ~

Update Software

Introduce

The software of the display panel (DP) and the electronic module (EM) can be updated separately. The

updating work should be done by a qualified person.

The tools used to update software are figured below.

As showed in the above figure, the USB cable is used to connect the laptop and MINICUBE2 main unit, and

the target cable is used to connect the MINICUBE2 and the target device (such as DP, or EM).

The following figure shows the parts name of MINICUBE 2 main unit.

How to update the software?

1.

Set the mode select switch to M2, and the power select switch to 5 on the MINICUBE2 unit.

2.

Power off the washing machine, and unplug the communication cable from DP or EM.

3.

Connect the laptop and MINICUBE2 using the USB cable. And connect the MINICUBE2 and DP or EM
using the target cable. The triangle mark on the target cable connector should be aligned with the
similar mark on the PCB of DP or EM (see figure below), in order to make sure to mate the connectors

«
...
18
19
20
21
22
...
»

Содержание 4000


































Отзывы:

Нет отзывов

Похожие инструкции для 4000

Бренд: Zanussi Страницы: 3

Бренд: Zanussi Страницы: 19

Бренд: Zanussi Страницы: 24

Бренд: Gaggenau Страницы: 68

Бренд: Gaggenau Страницы: 52

Бренд: Qilive Страницы: 178

Бренд: Kärcher Страницы: 90

Бренд: Maidaid Halcyon Страницы: 17

Бренд: OMEGA AIR Страницы: 37

Бренд: Feider Machines Страницы: 26

Бренд: Pacific Ears Страницы: 3

Бренд: Alto Страницы: 35

Бренд: Andis Страницы: 20

Бренд: Kärcher Страницы: 13

CLOTHES-PROCESSOR EZ 3600 CEE

Бренд: Equator Страницы: 16

Бренд: Jackson MSC Страницы: 64

Hotpoint HDA3400G

Бренд: Hotpoint Страницы: 2

Бренд: GE Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды