manualshive.com logo in svg

Apollo SA7800-870APO, Руководство пользователя

Поделиться
Скачать
Apollo SA7800-870APO Скачать руководство пользователя страница 27

MANAGEMENT

SYSTEMS

Assessed to ISO 9001:2008

Cert/LPCB ref. 010

Assessed to ISO 14001:2004

Cert/LPCB ref. 010 EMS

MANAGEMENT

SYSTEMS

Cert/LPCB ref. 010

PRODUCT

CERTIFICATION

Apollo Test Set - User Manual

27

(a)

(b)

If the device successfully passes the data 
restore operation, the ‘Data restored’ splash 
screen (a) appears. If the data restore is not 
successful the ‘Issue during restore operation’ 
splash screen appears along with details of 
the initial device settings (mode, polling LED 
status). 
Tap either ‘Retry’ or ‘Dismiss’ as appropriate.

‘Retry’ will start the test again.
‘Dismiss’ closes the Fast Test splash screen.

LED Test

To start the LED test, tap the LED 
test button. The button colour 
changes from grey to blue and the 
LED test is active.

Sensor status

The Sensor status section of the programmer mode splash screen is divided into three rows:

•  The top row shows the sensor type

•  The middle row shows the last sensor status - the colour of the text indicates its current state:

Blue 

- Fault

Green

 - normal

Orange

 - active

Red

 - alarm

•  The bottom row shows the raw sensor value - live temperature for a heat sensor, live optical sensor value or live 

CO sensor value.

Содержание SA7800-870APO



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды