API The BOX Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 97

background image

API “The BOX”

Operator’s Manual

17

2.2.4 Output Routing and Pan-Pot

Direct Output

Each input channel has a direct output intended to feed a DAW analog input while
recording. The direct output is fed post-fader/mute by default, but can be fed by the
preamp output. The direct output is always active except when the channel MUTE is
engaged.

DIRECT OUTPUTS / PRE OUTPUTS: DB-25, balanced, low-impedance, line-level

•

Outputs 1-4: Direct out (post-fader) or preamp output from input channels 1-4

o

Fed post-fader/mute by default (direct output)

o

Preamp output replaces post-fader output if DIR PRE is engaged

•

Outputs 5 & 6: Insert send from input channels 1 & 2

•

Outputs 7 & 8: Preamp outputs from input channels 3 & 4

•

Standard pin-out

: 1-4=direct or preamp outputs 1-4, 5-6=insert send 1-2, 7-8=preamp

outputs 3-4

Program Bus Assignment

Stereo Pan-Pot

PGM (Program): Assigns the input channel output to the program bus
when engaged

•

Program bus is fed post-pan-pot

•

Illuminates when engaged

PAN (pan-pot): Continuously variable left-right stereo pan-pot

•

Program bus is fed post-pan-pot

•

-3dB pan law (-3dB per side when panned center)

•

Center detent

DIR PRE (preamp direct output): Replaces the fader output with the
preamp output at the DIRECT OUTPUTS / PRE OUTPUTS DB-25
connector on the rear panel

•

Default feed is post-fader/mute if not engaged

•

Illuminates when engaged

The  DIRECT  OUTPUTS  /  PRE  OUTPUTS  connector
carries  direct  or  preamp  outputs  from  input
channels  1-4,  as  well  as  the  insert  send  from
input  channels  1  &  2  and  the  preamp  outputs
from input channels 3 & 4.

«
...
15
16
17
18
19
...
»

Содержание The BOX


































































































Отзывы:

Нет отзывов

Похожие инструкции для The BOX

Бренд: Nakamichi Страницы: 5

Бренд: Mackie Страницы: 24

Бренд: Behringer Страницы: 3

Бренд: Studio Technologies Страницы: 27

Бренд: Jata electro Страницы: 20

RED LLAMA Mk II WHE-203

Бренд: Way Huge Страницы: 2

Бренд: Fulltone Musical Products Страницы: 2

Бренд: Kogan Страницы: 8

Бренд: Black & Decker Страницы: 12

Бренд: Black & Decker Страницы: 12

Бренд: Black & Decker Страницы: 16

Бренд: Black & Decker Страницы: 32

Бренд: Black & Decker Страницы: 24

Бренд: Black & Decker Страницы: 26

HELIX MX610 Series

Бренд: Black & Decker Страницы: 2

Бренд: KitchenAid Страницы: 20

Бренд: KitchenAid Страницы: 10

Бренд: KitchenAid Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды