API The BOX Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 97

background image

API “The BOX”

Operator’s Manual

13

Rear Panel Preamp Connections

All four input channels have the same preamp input connections on the rear panel.

DIRECT OUTPUTS / PRE OUTPUTS: DB-25, balanced, low-impedance, line-level

•

Outputs 1-4: Direct out (post-fader) or preamp output from input channels 1-4

o

Fed post-fader/mute by default (direct output)

o

Preamp output replaces post-fader output if DIR PRE is engaged

•

Outputs 5 & 6: Insert send from input channels 1 & 2

•

Outputs 7 & 8: Preamp outputs from input channels 3 & 4

•

Standard pin-out

: 1-4=direct or preamp outputs 1-4, 5-6=insert send 1-2, 7-8=preamp

outputs 3-4

In addition to the DB-25 connector, input channels 3 & 4 have a separate preamp
output that’s part of an extra set of connections that support the 500 slots.

INSTRUMENT INPUT:

¼

” tip-sleeve, unbalanced, high-

impedance

•

MIC must be engaged to use this input

•

Replaces MIC signal as preamp input

MIC INPUT: 3-pin female XLR, balanced, low-impedance

•

MIC must be engaged to use this input

•

Provides phantom power when the 48v switch is
engaged

LINE INPUT:

¼

” tip-ring-sleeve, balanced, low-impedance

•

MIC must be disengaged to use this input

The  DIRECT  OUTPUTS  /  PRE  OUTPUTS  connector
carries  direct  or  preamp  outputs  from  input
channels  1-4,  as  well  as  the  insert  send  from
input  channels  1  &  2  and  the  preamp  outputs
from input channels 3 & 4.

PREAMP OUTPUT:

¼

” tip-ring-sleeve, balanced, low-

impedance, line-level

•

Not available on input channels 1 & 2

«
...
11
12
13
14
15
...
»

Содержание The BOX


































































































Отзывы:

Нет отзывов

Похожие инструкции для The BOX

Бренд: Bartscher Страницы: 13

Бренд: Samson Страницы: 2

Бренд: Yamaha Страницы: 26

350-Watt 12-Speed all Die-Cast Stand Mixer

Бренд: Oster Страницы: 20

Бренд: Jata electro Страницы: 20

Бренд: TONE WEAL Страницы: 8

Copper Tremolo CT-1

Бренд: Onerr Страницы: 11

Бренд: Tascam Страницы: 28

Бренд: American Audio Страницы: 26

INFINITE MINI SAMPLE SUSTAINER

Бренд: TC Electronic Страницы: 17

Бренд: Scarlett Страницы: 16

Бренд: Hamilton Beach Страницы: 28

Бренд: Nady Audio Страницы: 2

Бренд: EchoBandit Страницы: 8

Бренд: IBM Страницы: 64

Бренд: Hkoenig Страницы: 77

Бренд: Fulltone Страницы: 2

Бренд: M-Audio Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды