manualshive.com logo in svg

API 8512 Series, Руководство по эксплуатации и установке

Поделиться
Скачать
API 8512 Series Скачать руководство пользователя страница 7

MANUAL IM635

 

Safety Summary 

Page 7 

Personnel working with or near high voltage should be familiar with modern methods of resuscitation.  

DO  NOT  wear  jewelry  (rings,  bracelets,  metal  watches,  and/or  neck  chains)  while  working  on  exposed 
equipment.  Be  very  cautious  about  using  hand  tools  near  exposed  backplanes,  bus  bars,  and/or  power  supply 
terminals.  Use  properly  insulated  tools.  When  making  test  connections  to  the  power  supply  terminals  and  bus 
bars, use only insulated probe tips.  

Verify that the instrument is set to match the available line voltage and the correct fuse is installed.  

DO NOT install substitute parts or perform any unauthorized modification to this instrument. Contact Weinschel to 
acquire any information on replacement parts or returning the instrument for repair. Unauthorized modification 
can cause injury to personnel and/or destruction of the instrument.  

Operating  personnel  must  not  remove  instrument  covers.  Component  replacement  or  adjustments  must  be 
performed by qualified service personnel.  

DO NOT operate the instrument near or in the presence of flammable gases or fumes. 

1.3.

 

Detailed Precautions 

The following WARNINGS, CAUTIONS and  NOTES appear throughout the text  of this manual and are repeated 
here for emphasis. 

 

All  procedures  and/or  steps  identified  as  must  be  followed  exactly  as  written  and  according  to 
industry  accepted  ESDS  device  handling  procedures.  Failure  to  comply  WILL  result  in  ESD 
damage. 

 

DO NOT use a nylon bristle brush in any solvent as the bristles may dissolve and cause damage to the 
circuit card or component.  

 

DO NOT use ultrasonic cleaning on parts or assemblies containing electrical or electronic components.  

 

DO NOT bend pins of electrical connectors when using fiber-bristle brush.  

Compressed  air  used  for  cleaning  and/or  drying  can  create  airborne  particles  that  may  enter  the  eye. 
Goggles/face shields should be worn. DO NOT direct air stream towards self or other personnel. Pressure should 
be restricted to a maximum of 15 psi to avoid personal injury.  

Under no circumstances should a wire brush, steel wool, or abrasive compound be used on any surface. Using 
these items will cause extensive damage to the instrument's surface.  

 

DO  NOT  return  any  instrument  or  component  to  Weinschel  without  receiving  prior  factory 

authorization. 

1.4.

 

Safety Symbols 

The following symbols are used to identify safety hazards found throughout this publication and/or located on the 
instrument. 

 

Содержание 8512 Series




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды