manualshive.com logo in svg

API 8512 Series, Руководство по эксплуатации и установке

Поделиться
Скачать
API 8512 Series Скачать руководство пользователя страница 11

MANUAL IM635

 

Installation 

Page 11 

3.

 

If applicable, install the unit into rack or cabinet. Follow all manufacturer instructions regarding 

installation. 

4.

 

Connect all power, RF and communication cables as required to the unit. 

3.3.

 

Supply Voltage and Fuse 

Model 8512 module can be operated with 115 VAC power supply. An AC external switch, which is 
located on the rear panel of the UUT, allows user to power up the UUT with AC voltage. The Power 
Entry  Module  Assembly  located  on  the  rear  panel  contains  a  grounded  three-prong  AC  power 
connector, an on/off power switch, and a fuse drawer. 

The AC power connector is used to supply single-phase AC power to the unit. This connector also grounds the 
chassis of the unit when the AC power cable is connected to a grounded wall outlet. The supplied power cable or 
equivalent is recommended for safe operation. A grounded three-prong connection is required for safe operation. 

The on/off power switch is used to toggle power to the unit for normal operation. To supply power, set the switch 
to ON or |. To disconnect power, set the switch to OFF or O.  

The fuse drawer contains a 5 x 20mm 250 V fuse. The current rating of the fuse is listed on the rear of the unit. 
Do not install a fuse with a higher  current rating than the listed value. Electrical shock can occur if the unit is 
connected to AC power while changing the fuse. To prevent personal injury, disconnect the power cable from the 
unit and allow the internal power supply to discharge before removing the fuse. 

All electrical rack or chassis and machine elements should be Earth Grounded in installations where high level of 
electrical noise can be expected. The rack or chassis should be grounded with a rod or attached to a nearby earth 
structure  such  as  a  steel  beam  support  beam.  Connect  each  apparatus  to  a  single  ground  point  in  a  star 
configuration  with  low  impedance  cable.  Scrape  away  paint  and  other  nonconductive  material  from  the  area 
where  a  chassis  makes  contact  with  the  enclosure.  In  addition  to  the  ground  connection  made  through  the 
mounting bolt or stud, use a one-inch metal braid or size #8 AWG wire to connect between each chassis and the 
enclosure at the mounting bolt or stud.

 

3.4.

 

RF Port Connectors 

 

 

To  prevent  damage  to  the  device  do  NOT  exceed  the  maximum  allowable  power  level 

specifications  of  the  unit  at  any  port.  Use  a  calibrated  torque  wrench  to  tighten  all  RF 
connections. 

 

Based on selected options, a typical Model 8512 Series Switch Unit can contain up to 14 SP6T switches on the 
front  or  rear  panels  and  support  SMA  connections.  Connectors  are  per  MILSTD-348  interface  dimensions  and 
mate nondestructively per MIL-STD-212. 

3.5.

 

Ground Lug 

The unit contains a ¼-20 ground stud on the rear of the chassis for grounding purposes. 

 

Содержание 8512 Series




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды