AP TC5-1N5FAB Скачать руководство пользователя

Страница: 12 / 72

TC5-1N5FAB rev.06

TC5-1N5FAB

For each additional probe connected to the controller:

Press the push-button once again. If the probe is not defective, the

letters "

PR#

" (where # is the number of the input to which the probe is

connected) are displayed, alternating with the on/off state of the probe
and the temperature measured by the probe. If the probe is defective,
the letters "

PR#

" are displayed, alternating with the on/off state of the

probe and the letter "

Outside Probe:

If the outside probe is

defective, the display shows the letter
"

" when the parameter selection knob

is set to

OUTSIDE T

TAGE 3 OPERATION

Stage 3 can operate as a heating or cooling stage.

Set switch # 7 to

OFF

to use Stage 3

for cooling.

Set switch # 7 to

to use Stage 3

for heating.

TC5-1N5FAB rev.06

TECHNICAL SPECIFICATIONS

Supply:

- 115/230 VAC (-18%, +8%), 60 Hz, L1 same phases as Stage 1,

overload and overvoltage protection fuse F9 fast blow.

- 12 VDC for AC back-up supply; can activate stages 2-6 if supplied

with DC back-up voltage.

Stage 1:

Variable output, 60 Hz, 10A FAN (1/2 HP/115 VAC) / (1.5 HP/

230VAC), fuse F1-15A slow blow.

Stage 2:

ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 6A FAN,10A RES,

fuse F2-15A slow blow.

Stage 3:

ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 6A FAN,10A RES,

heating or cooling, fuse F3-15A slow blow.

Curtains:

OPEN-CLOSE output, 115/230 VAC, 60 Hz, 30VDC, 5A winch

output, fuse F6-5A slow blow.

Mist:

ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 6A FAN,10A RES, fuse

F5-15A slow blow.

Heater 1:

ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 6A FAN,10A RES,

heating, fuse F4-15A slow blow.

Alarm:

ON-OFF output, 115/230 VAC, 60 Hz, 30VDC, 3A , fuse F8-3A slow

blow.

Probes:

Low voltage ( < 5V), isolated from the supply. Operating range:

-40.0° to 120.0°F (-40.0° to 48.9°C). Accuracy: 1.8

F (1

C) between 41

and

F (5

and 35

C).

Enclosure:

ABS, moisture and dust-tight.

The room temperature where the controller is located MUST
ALWAYS REMAIN BETWEEN 32

AND 104

F (0

AND 40

C).

Содержание TC5-1N5FAB









































































Результаты поиска

Содержание TC5-1N5FAB

Отзывы:

Похожие инструкции для TC5-1N5FAB

Бренды по названию

Популярные бренды

AP TC5-1N5FAB, Руководство пользователя

Результаты поиска

Содержание TC5-1N5FAB

Отзывы:

Похожие инструкции для TC5-1N5FAB

Бренды по названию

Популярные бренды