AP Diving RBV07 Series Скачать руководство пользователя страница 49

Страница: 49 / 50

AP Diving Ltd. RBV07 Swivel Inflator Range Maintenance Manual

Page 49 of 50

7.17 Push sliding collar onto snap connector body

- The collar can only go on in one way. Push it on with the wider opening facing the hose

and the smaller opening facing the circlip, to be fitted in the next step.

- Again, make sure you do not lose one of the ball bearings during this step.

7.18 Refit circlip onto snap connector body

- Before fitting it back on, make sure it hasn’t been stretched and become too wide during

removal. If unsure: use a new circlip.

WARNING: If that is the case, it may come off again inadvertently during use,

rendering the whole hose connection and anything it is attached to inoperable!

- Just push it back on. Check that you can rotate it in its groove after fitting. It should

rotate, but only with slight difficulty. If it rotates too easily, it may have become too wide.
In that case remove it, tighten it up and refit it – or fit a new one.

This completes the re-assembly of the AP50 Medium Pressure hose.

Содержание RBV07 Series



















































Результаты поиска

Содержание RBV07 Series

Отзывы:

Бренды по названию

Популярные бренды

AP Diving RBV07 Series, Руководство по обслуживанию

Результаты поиска

Содержание RBV07 Series

Отзывы:

Бренды по названию

Популярные бренды