manualshive.com logo in svg

anvajo fluidlab R-300, Руководство пользователя

Поделиться
Скачать
anvajo fluidlab R-300 Скачать руководство пользователя страница 16

User Manual fluidlab R-300

 

 

 

Edition 202104 

 

 

 

 

 

 

 

17 

Vers.: 1.2 

4

 

Setup and Use 

 

Note:

 

 

If  used  as  a  portable  device,  the 

fluidlab 

R-300  must  be  held  in  one  hand  and 

operated with the other free hand.

 

If it is being used as a desktop device or when it 

is being charged, it should be placed on a stable, level, secure surface to prevent it 
from falling over and being damaged. 

 

 

Warning!

 

During the analysis, the device should be kept still. It is recommended that the device 
should be operated in a stationary manner on a stable surface.

 

 

4.1

 

Initial Setup 

 

Note:

 

On  delivery,  the 

fluidlab 

R-300  is  in  shipping  mode.

 

In  order  to  start  up  your 

fluidlab 

R-300 for the first time, please connect it to the supplied USB charger using 

the supplied USB cable before switching it on for the first time. 

 

1.

 

Remove  the  protective film from  the  device’s  display by  taking  hold  of  the 

small tab on the top right-hand edge of the film (near the power on/off button) 
and carefully pulling it off downwards over the display. 

2.

 

Connect the device to the supplied USB charger, the USB cable and a mains 
socket 

–

 the same procedure as when charging the battery (see Chapter 4.1). 

3.

 

The power on/off button (see Figure 2-2) lights up briefly. The device is no 
longer in shipping mode and can be switched on (see Chapter 4.2). 

 

4.1

 

Charging the Built-in Battery 

 

 

Warning!

 

Throughout the charging period, the 

fluidlab 

R-300 must be placed on a stable, level, 

secure, fire-resistant surface. The charging process may cause the bottom of the device 
to heat up.

 

 

 

Warning!

 

The device may only be charged and operated using the supplied power supply unit 
described  in  the  specifications  (Chapter 9.2).  If  the  power  supply  unit  fails,  a 
replacement power supply unit should be requested from the manufacturer.

 

 

 

 

Warning!

 

Only charge the battery in the specified nominal  operating  range (see Chapter  9.1)! 
Failure to observe this instruction may result in permanent damage to the battery.

 

 

1.

 

Place the 

fluidlab 

R-300 on a stable, level, secure, fire-resistant surface. 

2.

 

Plug the supplied USB charger (Figure 1

–

3) into a mains socket. 

3.

 

Plug the larger of the two connectors on the USB cable (Figure 1

–

6) into the 

USB port on the USB charger. 

Содержание fluidlab R-300






































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды