Antunes 9710124 Скачать руководство пользователя страница 3

UFL-500 SERIES

3

®

P/N 1012043 Rev B 11/19 

Safety Information

Installation

 

y

Read and understand all 

instructions before installing 

or using the unit.

 

y

Install and locate the equipment 

only for its intended use as 

described in this manual.

 

y

This equipment is to be 

installed to comply with the 

local plumbing code and any 

other applicable code.

 

y

This equipment should be 

supplied with only cold water.

 

y

Water pressure must not 

exceed 100 psig (690 kPa).  

To reduce water pressure, install 

a water pressure regulator and 

set to suit the application.

 

y

The trans membrane pressure 

(inlet pressure minus the 

permeate water pressure) must 

not exceed 45 psi (310 kPa).

 

y

A ground fault circuit interrupter 

(GFCI) must be installed on 

the circuit to this system.

 

y

When installed on metallic 

plumbing, a properly sized 

electrical bonding jumper must 

be installed across the inlet and 

outlet pipes serving this unit.

 

y

For installations in Massachusetts, 

the Commonwealth of 

Massachusetts Plumbing Code 248 

CMR shall be adhered to. The use 

of saddle valves are not permitted. 

Please consult your local plumber.

NOTE:

 If the inlet water pressure is 

less than 50 psig (345 kPa), 

it is recommended that a 

suitably-sized booster system 

(outlet pressure 60 psig - 100 

psig max (414 kPa - 690 kPa 

max) be installed.

WARNING

ELECTRICAL SHOCK HAZARD.   

Failure to follow the instructions in 

this manual could result in serious 

injury or death.

DO NOT modify the power supply 

cord plug. If it does not fit the outlet, 

have a proper outlet installed by a 

qualified electrician.
DO NOT use an extension cord with 

this unit. 

If the supply cord is damaged, it must 

be replaced by the manufacturer, its 

service agent, or a similarly qualified 

person.
All electrical connections must be in 

accordance with local electrical codes 

and any other applicable codes.

 

Operation

 

y

DO NOT operate the unit if it has 

been damaged or dropped, if 

it has a damaged cord or plug, 

or if it is not working properly.

 

y

DO NOT block or cover any 

openings on the equipment.

 

y

DO NOT immerse the cord, 

unit, or power plug in water.

 

y

Keep the cord away from 

heated surfaces. 

Maintenance

 

y

DO NOT use corrosive 

chemicals in this equipment.

 

y

DO NOT clean the unit with a 

water jet or steam cleaner.

Service

 

y

 Unplug the power cord before 

performing any service or 

maintenance on the unit.

 

y

If the supply cord is damaged, 

it must be replaced by the 

manufacturer, its service agent, or 

a similarly qualified person in order 

to avoid an electrical hazard.

 

y

This equipment should be serviced 

by qualified personnel only. 

Contact Antunes for repair.

Содержание 9710124



















Отзывы: