Antunes 9200641 Скачать руководство пользователя страница 10

Страница: 10 / 24

VERTICAL CONTACT TOASTER

P/N 1011287 Rev. E 02/18

Conveyor Belt Chains

MEASURING THE CONVEYOR BELT CHAINS

1. Facing the toaster, locate the approximate center-

point of the Conveyor Chain.

2. Pull the Conveyor chain away from the edge of

the toaster. Stand a U.S. Dime, 11/16” (1.8 cm)

coin on end between the frame and the chain.

If the gap is significantly wider than the coin,

REMOVE links as described in the section titled

Adjusting The Conveyor Belt Chains

. Then,

measure the gap again to make sure it is not too

tight.

Check the opposite side of the toaster using the

same measurements.

MAINTENANCE (continued)

Figure 9. Removing Conveyor Belt Chain

Rotation

Upper Yellow Support Rod

Large Link

P/N 0800121

Small Link

P/N 0800204

NOTE: If the belt is too short (tight) to be reas-

sembled, remove an additional 1/2” link and install

a 3/4” link. This will make the conveyor belt 1/4”

shorter and enable it to be reassembled.
IMPORTANT: This is not covered under warranty. It

is a user responsibility.

REMOVING THE CONVEYOR BELT CHAINS

1. Turn the unit off, unplug the power cord, and allow

the unit to cool down.

2. Remove the Heat Shield, front and rear Conveyor

Covers, and Release Sheet (Figure 4).

NOTE: When replacing the Conveyor Belt chain, be

sure to clean the Release Sheet as well.

3. Set the Bun Thickness Compression Control

knobs to 6.

4. Disconnect the Conveyor Belt chain by squeezing

any two links together and unhooking both ends

of one link (Figure 8). A needle-nose pliers may

be required. Remove the Conveyor Belt chain.

NOTE: With conveyor belt removed, the tensioner

assemblies (4, page 24) and slide rails (40, page 24)

can be replaced.

Figure 8. Measuring Conveyor Belt Chains

ADJUSTING THE CONVEYOR BELT CHAINS

After a period of time, the conveyor belt links will wear

and the conveyor belt will stretch. This will eventually

cause the conveyor to jam as it rotates on the sprock-

ets. This is easily remedied by removing one or more

conveyor links from each side of the belt.
There are four 1/2” pitch links on each conveyor belt.

The rest of the links are 3/4”.
1. Remove the Conveyor Belt Chain as described in

the section titled

Removing the Conveyor Belt

Chains

2. To shorten a stretched Conveyor Belt chain,

remove one 1/2” link from the belt.

3. Reassemble the Conveyor Belt Chain to the

sprockets as described in the section titled

Replacing the Conveyor Belt Chains

Содержание 9200641

























Результаты поиска

Содержание 9200641

Отзывы:

Похожие инструкции для 9200641

Бренды по названию

Популярные бренды

Antunes 9200641, Руководство пользователя

Результаты поиска

Содержание 9200641

Отзывы:

Похожие инструкции для 9200641

Бренды по названию

Популярные бренды