Antunes 9200641 Скачать руководство пользователя страница 9

Страница: 9 / 24

VERTICAL CONTACT TOASTER

P/N 1011287 Rev. E 02/18

WARNING

Turn the unit off, disconnect the power source

and allow the unit to cool down before performing

any service or maintenance on the unit.

NOTE: As of March 2017, the Interlock Switch was

removed from use. If your toaster has the Interlock

Switch, you will need to place the Heat Shield onto

the toaster in order for the conveyors to turn. If

your toaster does not have an Interlock Switch, the

conveyors will turn as long as the unit is on.
NOTE: Check the Release Sheet to make sure it is

not caught in the Conveyor Belt Chain. Additional

Release Sheets can be obtained by ordering part

number 7000249 (3 pack) or 7000250 (10 pack).

Daily

CLEANING THE ACCESSORIES

1. Turn the unit off, unplug the power cord, and

allow the unit to cool for 30 minutes.

2. Remove the Heat Shield and Bun Chute. Wash

these items in soapy water, rinse with clear water,

sanitize, and allow to air dry.

3. Wipe down the outside of the toaster with a

slightly damp cloth and allow to air dry.

CLEANING THE RELEASE SHEET

1. Make sure the unit is turned off, the power cord is

unplugged, and the unit is cool. Put on heat resis-

tant gloves. Remove the Release Sheet (Figure

7).

2. Lay the Release Sheet on a clean, flat, dry sur-

face. Apply an appropriate cleanser to a clean,

dry towel.

3. Wipe the towel firmly across the Release sheet

from top to bottom over its entire surface. Repeat

this procedure with a clean, dry towel dampened

with water.

4. Next, wipe the Release Sheet with a clean towel

dampened with sanitizer and allow to air dry.

Repeat Steps 3 through 4 on the reverse side of

the Release Sheet.

5. Remove the front and rear Conveyor Covers

(Figure 4). Wipe the exterior of Conveyor Belt

chains with a clean, sanitized towel.

6. Install front and rear Conveyor Covers (Figure

4) and turn the unit on. Count to 10, then turn

toaster off. Remove the front and rear Conveyor

Covers again and wipe newly exposed section of

the Conveyor Belt chains. Re-install the front and

rear Conveyor Covers.

7. Install the Release Sheet by draping it over both

sides of the Platen with the crease centered

directly on the Platen (Figure 7).

8. Install the Heat Shield (Figure 7). The Heat

Shield clips fit over the tip of the Platen and retain

the Release Sheet in place.

MAINTENANCE

CAUTION

To prevent damage to the unit, do not use abra-

sive cleaners on the release sheet.

Heat Shield

Platen

Release Sheet

Interlock Switch

(Some Models)

Figure 7. Removing/Installing the Release Sheet

Содержание 9200641

























Результаты поиска

Содержание 9200641

Отзывы:

Похожие инструкции для 9200641

Бренды по названию

Популярные бренды

Antunes 9200641, Руководство пользователя

Результаты поиска

Содержание 9200641

Отзывы:

Похожие инструкции для 9200641

Бренды по названию

Популярные бренды