Antunes 9200641 Скачать руководство пользователя страница 7

Страница: 7 / 24

VERTICAL CONTACT TOASTER

P/N 1011287 Rev. E 02/18

NOTE: As of March 2017, the Interlock Switch was

removed from use. If your toaster has the Interlock

Switch, you will need to place the Heat Shield onto

the toaster in order for the conveyors to turn. If

your toaster does not have an Interlock Switch, the

conveyors will turn as long as the unit is on.
NOTE: Check the release sheet to make sure it

is not caught in the conveyor. Additional release

sheets can be obtained by ordering part number

7000249 (3 pack) or 7000250 (10 pack).

Equipment Setup

When placing the toaster into service, pay attention to

the following guidelines.

• Make sure power to the unit is off and the toaster

is at room temperature.

  •  Do not block or cover any openings on the unit.
  •  Do not immerse cord or plug in water.
  •  Keep cord away from heated surfaces.
  •  Do not allow cord to hang over edge of table or

counter.

Connect the unit to the power supply. Refer to the

specification plate for the proper voltage.

Figure 3. Folding Release Sheet

Lay sheet on a flat surface

Fold over so ends meet

Press lightly with finger to

form crease

Figure 4. Installing Release Sheet

Platen

Conveyor Cover

Heat Shield

Release Sheet

Conveyor Interlock

Switch (Some

Models)

WARNING

ELECTRICAL SHOCK HAZARD. FAILURE TO

FOLLOW THE INSTRUCTIONS IN THIS MANUAL

COULD RESULT IN SERIOUS INJURY OR DEATH.

• Electrical ground is required on this appliance.

• Do not modify the power supply cord plug. If

it does not fit the outlet, have a proper outlet

installed by a qualified electrician.

• Do not use an extension cord with this appliance.

• The toaster should be grounded according to local

electrical codes to prevent the possibility of electri-

cal shock. It requires a grounded receptacle with

separate electrical lines, protected by fuses or cir-

cuit breaker of the proper rating.

• Check with a qualified electrician if you are in

doubt as to whether the appliance is properly

grounded.

CAUTION

Bread may burn. Therefore toasters must not be

used near or below curtains or other combus-

tible walls and materials. Failure to maintain safe

operating distances may cause discoloration or

combustion.

All electrical connections must be in accordance

with local electrical codes and any other appli-

cable codes.

INSTALLATION (continued)

Содержание 9200641

























Результаты поиска

Содержание 9200641

Отзывы:

Похожие инструкции для 9200641

Бренды по названию

Популярные бренды

Antunes 9200641, Руководство пользователя

Результаты поиска

Содержание 9200641

Отзывы:

Похожие инструкции для 9200641

Бренды по названию

Популярные бренды