manualshive.com logo in svg

ANTONUS STEP BROTHER, Руководство пользователя

Поделиться
Скачать
ANTONUS STEP BROTHER Скачать руководство пользователя страница 21

20

Now raise the CLOCK FM slider a little higher so that the 

positions assigned to GATE BUS 1 will step three times faster 
than normal. This adjustment can be facilitated by assigning 
the first three positions to GATE BUS 1, skipping 4, assigning 
5 through 7, skipping 8, and so on. This arrangement will pro-
duce a triplet 1 rhythm where the first three positions take 
the same time as the 4th does by itself.

Set the SKIP/OFF/RESET switch to RESET. Put the 5thGA-

TE ASSIGN switch to the low position and observe that the 
resultant four note sequence can still be modified rhythmi-
cally by setting the various GATE ASSIGN switches to either 
GATE BUS 1 or the middle (GATE BUS 2) positions.

Try different rhythms and different combinations of GATE 

ASSIGN switches. Notice that the SKIP function still works 
and that any note in the sequence can still be eliminated by 
“skipping”. 

Five simple steps for an instantaneous sequence: 

These five steps were designed to help you establish a ba-

sic sequence, very quickly. You must have consider this for-
mat each time you set up sequential patch, even after you 
have experience in the manipulation of controls.

Step 1:   Connect the sequencer to the synthesizer, just like
 

is described in Chapter V.

Step 2:   Configure the controls at your sequencer with the
 following 

way:

 

a. Sequential mode 16/1.

 

b. clock stopped

 

c. Press the reset button.

Step 3:   Set the patch on the synthesizer you want to control.

Step 4:   Open the filter or the amplifier so you can listen to 
 

the oscillator you are tuning. Tune each step, one by 

 

one until you have completed the desired pattern.

Step 5:   Press the start/stop button, and go!

VI. 4. USING GATE ASSIGN FOR ACCENTS

Set all the GATE ASSIGN switches up to the GATE BUS 1 

position and close the CLOCK FM slider. Now remove the 
patch cord from the CLOCK OUT jack and plug it into the 
jack marked CLOCKED GATE 1 OUT. Set the release time 
on your synthesizer’s envelope generator about half way 
up. Now start the sequencer CLOCK. Aside from the longer 
release time, you should not notice any difference at this 
point. Now start moving GATE ASSIGN switches back to the 
middle position. Notice that you will not get a new attack on 
a note unless the GATE ASSIGN switch is on GATE BUS 1. If 
you move all the GATE ASSIGN switches to the middle posi-
tion, there will be no sound at all. Try it! 

Try bringing the GATE ASSIGN switches back up one at a 

time. 

Try using the GATE ASSIGN switches, along with the 

RESET and SKIP functions to create some interesting 
rhythms.

VI.5. CLOCK PULSE WIDTH

Just like the VCO on your synthesizer, the CLOCK in your 

sequencer produces a pulse wave output of variable duty cy-
cle. You may recall the following illustration:

Содержание STEP BROTHER












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды