ANTEK ECE3AP-00-01 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 18

ANTEK ECE3AP-00-01 Скачать руководство пользователя страница 14

Antriebstechnik GmbH

Technical Documentation EC863 and ECE3AP-00-01

Page 14 of 18

(02/99) R0047GB.DOC

tH

Run-up time of the set value integrator

tR

Reverse running time of the set value integrator
Setting the set value slope

Specify set value jump (0

→

10 V) at the set value input and set the

desired speed slope with trimmer „tH„ and/or „tR„.
Setting range:

100 ms ... 2 s

Works setting:

2 s

internal

Set value

10V

100ms

Signal after set value jump

tH

tR

2s

0V

t

100ms

2s

PI

Setting of the speed control behaviour. When necessary adjust to
the respective application. Clockwise rotation increases the
proportional amplification.

Incorrectly set control behaviour leads to vibrations of the drive
which can destroy the motor or other components connected
downstream (gears etc.).
The manufacturer is not liable for damages which are caused by
incorrect parametrisation.
Works setting

Middle

n1, n2

Fixed speeds n1 and n2. This function can be selected with the plug
bridge STB3 „set value source„ (see chapter 0).
Works setting:

n1 = 4538 r.p.m.

n2 = 1396 r.p.m

«
...
12
13
14
15
16
...
»

Содержание ECE3AP-00-01



















Отзывы:

Нет отзывов