ANTAIRA LNX-602N страница 28 Скачать руководство пользователя

Страница: 28 / 39

LNX-602N User’s Manual

Antaira Technologies, LLC

Time (4-30)

Rapid Spanning-Tree Protocol learning and listening states to the

forwarding state. Enter a value between 4 through 30.

Path Cost

(1-200000000)

The cost of the path to the other bridge from this transmitting

bridge at the specified port. Enter a number 1 through

200000000.

Priority (0-240)

Decide which port should be blocked by priority in LAN. Enter a

number 0 through 240. The value of priority must be the multiple

of 16

Admin P2P

Some of the rapid state transactions that are possible within

RSTP are dependent upon whether the port concerned can only

be connected to exactly one other bridge (i.e. It is served by a

point-to-point LAN segment), or it can be connected to two or

more bridges (i.e. It is served by a shared medium LAN segment).

This function allows the P2P status of the link to be manipulated

administratively. True means P2P enabling. False means P2P

disabling.

Admin Edge

The port is directly connected to end stations, and it cannot create

bridging loop in the network. To configure the port as an edge

port, set the port to “

True

”.

Admin Non STP

The port includes the STP mathematic calculation.

True

is not

including STP mathematic calculation.

False

is including the

STP mathematic calculation.

Apply

Click “

Apply

” to activate the configurations.

NOTE:

Follow the rule to configure the MAX Age, Hello Time, and Forward Delay Time:

2 x (Forward Delay Time value –

1) ≥ Max Age value ≥ 2 x (Hello Time value +1)

RSTP Information

Show RSTP algorithm result at this table.

Содержание LNX-602N








































Результаты поиска

Содержание LNX-602N

Отзывы:

Похожие инструкции для LNX-602N

Бренды по названию

Популярные бренды

ANTAIRA LNX-602N, Руководство пользователя

Результаты поиска

Содержание LNX-602N

Отзывы:

Похожие инструкции для LNX-602N

Бренды по названию

Популярные бренды