ANTAIRA APX-110N5 Скачать руководство пользователя страница 42

Страница: 42 / 68

Noise Immunity:

Check to enable. When enabled, it automatically adjusts the signal/noise level for best

performance. In low noise environment it is recommended to turn off this function.

Signal Strength Indicator (RSSI):

The default values are LED1-Red (10), LED2-Yellow (20), LED3-Green (40) Each LEDs

when turn on indicates the RSSI signal strength has hit over the value. e.g. When LED1

and LED2 light up it indicate the RSSI is greater than 20.

When all 4 LEDs light up it indicate RSSI is greater than 40.

For long distant installation when signal strength expected to be about 20-30, the values

can be adjusted to display over this new range.

e.g. the LEDs values can be adjusted as follows:

LED1 (RSSI value=7)

LED2 (RSSI value=15)

LED3 (RSSI value=22)

LED4 (RSSI value=27)

Station Isolation:

When checked, prevent wireless clients on same AP from discovering other clients.

Chainmask Selection:

Available selections are: a)

1x1 Left Chain

, b)

1x1 right Chain

and c)

2x2 Dual

Chain

Selecting

1x1 Left Chain

will forced radio card to operate with 1transmit and 1

receive stream and both transmit /receive on the left port of radio card only.

Selecting

1x1 Right Chain

will forced radio card to operate with 1 transmit and 1

receive stream and both transmit /receive on the right port of radio card only.

Selecting

2x2 Dual Chain

(default) will enable radio card to operate with 2 transmit

and 2 receive streams and automatically transmit /receive on any of the 2 radio card

ports.

Содержание APX-110N5





































































Результаты поиска

Содержание APX-110N5

Отзывы:

Похожие инструкции для APX-110N5

Бренды по названию

Популярные бренды

ANTAIRA APX-110N5, Руководство пользователя

Результаты поиска

Содержание APX-110N5

Отзывы:

Похожие инструкции для APX-110N5

Бренды по названию

Популярные бренды