ANTAIRA APX-110N5 Скачать руководство пользователя страница 54

Страница: 54 / 68

Rx invalid NWID

value represents the number of packets received with a different NWID

or ESSID - packets which were destined for another access point. It can help to detect

configuration problems or identify the adjacent wireless network existence on the same

frequency.

Rx Invalid Crypt

value represents the number of transmitted and received packets which

were encrypted with the wrong encryption key and failed the decryption routines. It can be

used to detect invalid wireless security settings and encryption break attempts.

Rx Invalid Frag

value represents the number of packets missed during transmission and

reception. These packets were dropped due to re-assembling failure as some link layer

fragments of the packet were lost.

Tx Excessive Retries

value represents the number of packets which failed to be

delivered to the destination. Undelivered packet are retransmitted a number of times

before an error occurs.

Missed beacons

value represents the number beacons (management packets sent at

regular intervals by the Access Point) which were missed by the client. This can indicate

that the wireless client is out of range.

Other errors

value represents the total number of transmitted and received packets that

were lost or discarded for other reasons.

More Status

In More Status option contains some useful tools and additional status pages.

Ping Utility

– a ping tool to test the connectivity between devices.

Содержание APX-110N5





































































Результаты поиска

Содержание APX-110N5

Отзывы:

Похожие инструкции для APX-110N5

Бренды по названию

Популярные бренды

ANTAIRA APX-110N5, Руководство пользователя

Результаты поиска

Содержание APX-110N5

Отзывы:

Похожие инструкции для APX-110N5

Бренды по названию

Популярные бренды