Anite NEMO FSR1 Скачать руководство пользователя страница 101

Страница: 101 / 137

PC T EL

1 0 1

Delay

option enables/disables delay profile scanning. Delay is defined as the measured

difference between the expected arrival time (GPS time) and the actual arrival time of the

maximum peak above the PN threshold. It is reported in chips.

4. After making the appropriate settings, click OK and OK again and go to online mode to start

the scanning.

5. A green light on the scanner Device Status window should start blinking. This means that the

device is working properly and scanning using the default settings.

6. Click the Start Recording button

to start recording the results in an output file.

Spectrum Scanning

♦

Spectrum scanning is enabled on PCTEL EX scanners only in online mode. Hence, the

device needs to be added to Nemo Outdoor in online mode to activate the Spectrum

scanning functionality

1. After the PCTEL EX scanner is connected and activated in Nemo Outdoor, open the

Measurement Properties

dialog by selecting

Measurement | <device> | General

Properties

2. In the

Measurement Properties

dialog, go to the

Spectrum scanning

page.

Содержание NEMO FSR1










































































































































Результаты поиска

Содержание NEMO FSR1

Отзывы:

Anite NEMO FSR1, Руководство пользователя, Страница: 101 / 137

Результаты поиска

Содержание NEMO FSR1

Отзывы: