andrews CWH120/200 Скачать руководство пользователя страница 32

Страница: 32 / 44

INSTALLATION

SECTION 3

CWH 30

CWH 60

CWH 90

CWH 120

Mains On
Indicator

Status

Temperature

Diagnostic Code

Flashing Green

- Standby

Continuous Green

- Burner On

Red On

- Check Diagnostic Code

Lighting Instructions

•

Read Instruction Manual before use

•

Ensure storage tank is full before starting

•

To start move main switch to ON

•

Heater will work Automatically according to
demand

•

In case of failure refer to manual or call Service
Engineer

0 - Standby

1 - Heat Demand

- Circulation

Pump On

Reset

CONTROL

PANEL

The operational status of the water heater can be seen and the desired temperature can
be set on the control panel (Fig.11).

A green and a red LED can be found on the control panel for each burner module.
These indicate the status of the corresponding burner module.

The green LED:
- off

no automatic burner detected

- flashing

automatic burner detected, burner module not in use

- on

burner module in use

The red LED:
- off

no fault

- flashing

blocking fault

- on

locking fault

The display on the control panel consists of 3 segments, the following codes can appear:

Code

Meaning

No heat demand

Flashing, water heater not enabled

Heat demand

Programme changed water heater temperature activated

Permanent, circulation pump connected to terminals pump L - pump N activated

Flashing, circulation pump stand by

Actual water heater temperature

The water heater is
equipped with 1, 2, 3
or 4 burner modules
depending on the
model. Each burner
module has its own
automatic burner.

Fig . 11

CWH HEAT

EX CHANGER

CONFIGURATION

MAXXflo_Manual_Dec08_QX2 12/1/09 1:13 pm Page 33

Содержание CWH120/200













































Результаты поиска

Содержание CWH120/200

Отзывы:

Похожие инструкции для CWH120/200

Бренды по названию

Популярные бренды

andrews CWH120/200, Руководство по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CWH120/200

Отзывы:

Похожие инструкции для CWH120/200

Бренды по названию

Популярные бренды