background image

UG-783 

EVAL-ADXRS290Z-M User Guide

 

Rev. 0 | Page 2 of 14 

TABLE OF CONTENTS 

Features .............................................................................................. 1

 

Documents Needed .......................................................................... 1

 

Equipment Needed ........................................................................... 1

 

Typical Setup for the Inertial Sensor Evaluation System............. 1

 

General Description ......................................................................... 1

 

Revision History ............................................................................... 2

 

Getting Started .................................................................................. 3

 

Software Installation Procedures ................................................ 3

 

Evaluation Board Hardware Setup Procedures ........................ 7

 

Evaluation Board Hardware ........................................................ 7

 

Power Supplies .............................................................................. 7

 

Jumper Settings ..............................................................................7

 

Evaluation Board Circuitry ..........................................................7

 

How to Use the Software for Testing ..............................................8

 

Getting Started ...............................................................................8

 

Configuration Tab .........................................................................9

 

Real Time Data Tab .................................................................... 10

 

Noise Tab ..................................................................................... 11

 

Power Consumption Tab ........................................................... 12

 

Temperature Tab ......................................................................... 13

 

 

 

REVISION HISTORY 

1/15—Revision 0: Initial Version 

Содержание EVAL-ADXRS290Z-M















Отзывы: