background image

UG-439 

Evaluation Board User Guide

 

Rev. A | Page 2 of 13 

TABLE OF CONTENTS 

Features .............................................................................................. 1

 

General Description ......................................................................... 1

 

Digital Picture of the ADP5034 TSSOP Evaluation Board ......... 1

 

Revision History ............................................................................... 2

 

Using the Evaluation Board ............................................................. 3

 

Powering Up the Evaluation Board ............................................ 3

 

Measuring Evaluation Board Performance .................................. 4

 

Measuring Output Voltage .............................................................. 8

 

Measuring Ground Current .............................................................9

 

Measuring Ground Current Consumption of LDO Regulators
..........................................................................................................9

 

Evaluation Board Schematic and Artwork .................................. 10

 

Ordering Information .................................................................... 13

 

Bill of Materials ........................................................................... 13

 

Related Links ................................................................................... 13

 

 

REVISION HISTORY 

4/2017—Rev. 0 to Rev. A 

Changes to General Description Section and Figure 1 ............... 1 
Changes to Enable Section, Table 1, and Turning on the 
Evaluation Board Section ................................................................ 3 
Changes to Figure 4 .......................................................................... 4 
Added Figure 7 and Figure 9; Renumbered Sequentially ........... 5 
Changes to Measuring Load Regulation of Buck Regulator 
Section, Figure 8, Measuring Line Regulation of Buck Regulator 
Section, and Figure 10 ...................................................................... 5 

Added Figure 11 ................................................................................ 6 
Changes to Measuring Efficiency of Buck Regulator Section and 
Figure 12 Caption .............................................................................. 6 
Moved Measuring Ground Current Consumption of LDO 
Regulators Section ............................................................................. 9 
Changes to Figure 16...................................................................... 11 
Changes to Table 3 .......................................................................... 12 
 

8/2012—Revision 0: Initial Version 

 

Содержание ADP5034














Отзывы: