Analog Devices ADDS-21992-EZLITE Скачать руководство пользователя страница 35

Страница: 35 / 62

ADSP-21992 EZ-KIT Lite Evaluation System Manual

4-30

The ADSP-21992 EZ-KIT Lite board is laid out with separate analog and digital ground planes,
labeled AGND and DGND, respectively. JP1 is a link that connects the analog and digital ground
planes of the ADSP-21992 EZ-KIT Lite board.

NOTE

: For correct operation, this link must not be removed.

The arrangement on the input power supply connector is illustrated in

Figure 4-2.

AGND

5
4
3

-AVDD (-5V)

DGND

+AVDD (+5V)

VDD (+5V)

2
1

Figure 4-2: Power Supply Connector of ADSP-21992 EZ-KIT Lite Board

LEDs are provided to indicate that the power supplies are working correctly. The Power Supply
LEDs are listed in

Table 4-1:

LED

Power Supply Signal

CR1

+2.5V (DSP Core Voltage Supply)

CR2

+3.3V (Vddext)

CR3

+2.5V (+AVdd)

CR4

- 2.5V (-AVdd)

Table 4-1: Power Supply LEDs

4.2.2 Reset Generation

The ADSP-21992 can be reset from a number of sources on the ADSP-21992 EZ-KIT Lite board.
The sources of reset for the ADSP-21992 DSP are:

•

POR (power-on reset output pin of the ADSP-21992)

•

Reset button (S1)

•

External power on reset IC (A7)

•

USB Interface (software tools reset)

Содержание ADDS-21992-EZLITE































































Результаты поиска

Содержание ADDS-21992-EZLITE

Отзывы:

Похожие инструкции для ADDS-21992-EZLITE

Бренды по названию

Популярные бренды

Analog Devices ADDS-21992-EZLITE, Руководство пользователя

Результаты поиска

Содержание ADDS-21992-EZLITE

Отзывы:

Похожие инструкции для ADDS-21992-EZLITE

Бренды по названию

Популярные бренды