Installation Guide
PS-POE-AF-TC
802.3af Compliant PoE Injector
Overview
The PS-POE-AF-TC (
FG423-83
) is a 802.3af-compliant Power-over-
Ethernet (PoE) power supply with integral DC Injector (FIG. 1). It provides
DC power for one PoE-equipped device by "Injecting" DC power through
the CAT5 ethernet cable.
The PS-POE-AF-TC supports the IEEE standard PoE pinout: Pins 4&5
Power (+) / Pins 7&8 Power (-). See
Pin Connections
(on reverse) for
details.
Key features include:
•
Power over Ethernet (PoE)
•
10/100/1000 (MbPS) Data Rates
•
Self-contained Injector
•
100-240VAC Universal Input
•
Desktop Style / Non-vented Case
•
IEEE802.3af Compliant Detection, Disconnect, Overload and Over
Voltage Control Function
•
Load Diagnostic LED
•
UNH IOL Test Report
•
Over Load Shutdown and Short Circuit Protection
•
Regulated Output With Low Ripple
•
Meets Safety Agency Requirements
•
Complies with EMI/RFI Regulations
Product Specifications
Safety Information
Important Safety Information
•
The PS-POE-AF-TC should be connected to PoE networks only, without
routing to an outside network.
•
Only qualified personnel can install or remove the PS-POE-AT-TC.
•
AC Power Cord Set:
* The power cord must have regulatory agency approval for the specific
country in which it is used (for example, UL, CSA, VDE, etc.)
* The power cord must be a three-conductor type (two current-carrying
conductors and one ground conductor) terminated on one end by an IEC
60320 appliance coupler (for connection to the PS-POE-AT-TC), and on
the other end by a plug containing a ground (earthing) contact.
* The power cord must be rated for a minimum of 250 VAC RMS
operation, with a minimum rated current capacity of 5 amps or a minimum
wire gauge of 18 AWG (0.75 mm
2
).
•
A PS-POE-AF-TC installed in Australia requires power cords with a
minimum wire gauge of 16 WWG (1.0 mm
2
).
•
The PS-POE-AF-TC
DATA IN
and
DATA & POWER OUT
ports are
shielded RJ45 data sockets. They CANNOT be used as Plain Old
Telephone Service (POTS) telephone sockets. Only RJ45 data connectors
may be connected to these sockets.
•
The AC wall socket-outlet must be near the PS-POE-AF-TC and easily
accessible. You can remove AC power from the PS-POE-AF-TC by
disconnecting the AC power cord from either the wall socket-outlet or the
PS-POE-AF-TC appliance coupler.
•
The PS-POE-AF-TC “Data In” and “Data & Power Out” interfaces are
qualified as Safety Extra-Low Voltage (SELV) circuits according to IEC
60950-1. These interfaces may only be connected to SELV interfaces on
other equipment.
FIG. 1
PS-POE-AF-TC Power-Over-Ethernet Power Supply
PS-POE-AF-TC Specifications
Input Specifications
AC Input Voltage Range: 100-240VAC
Line Frequency:
47-63Hz
AC Input Current:
0.5A MAX at 110-240 VAC
Protection:
• Internal Primary Current Fuse
• Inrush Limiting
Input Power Cord:
150cm IEC power cord terminated with a
grounded Edison plug for AC input
Output Specifications:
Output Voltage:
48 VDC Nominal
Output Current:
375mA
Output Power:
15.4 Watts guaranteed
Ripple and Noise:
Below the IEEE802.3af requirements
• f<500Hz: Vp-p Max
• 500Hz to 150kKHz: Vp-p Max
• 150KHz to 500KHz: Vp-p Max
• 500KHz to 1MHz: Vp-p Max
Protection:
• Foldback Overcurrent Protection
• Short Circuit Protection
PS-POE-AF-TC Specifications (Cont.)
Output Specifications (Cont.):
Transient Response:
Meets IEC61000-4-4 (1Kv)
Leakage Current:
Up to 3uA
Efficiency:
81%
Hold-Up Time:
18.4msec at 90VAC
General Specifications:
LEDs:
•
Yellow (On):
power is on and active)
•
Green (On):
A remote terminal is connected.
•
Green (Blinking):
Overload state or short
circuit
Weight:
• Without cord: 0.40 lbs (181.43 g)
• With cord: 0.75 lbs. (340.19 g
Dimensions (HWD):
5.5" x 2.09” x 1.28" (14 cm x 5.3 cm x 3.25 cm)
Enclosure:
Molded black matte plastic
Cord and Connectors:
Dual RJ45 jacks built into the enclosure
Compliances:
• 802.3 AF compliant
• FCC Part 15 Class B
• CE EN55022 Class B and EN55024
• LVD EN 60950-1
• VCCI
• UL/cUL UL60950-1
• GS IEC 60950-1
Environmental Specifications:
Operating Temp:
32°F to 104°F (0°C to 40°C)
Storage Temp:
-4° F to +158° F (-20° C to +70° C)
Relative Humidity:
Non-Condensing 10% to 95%
