manualshive.com logo in svg

Amsco RELIANCE 300, Руководство по установке

Поделиться
Скачать
Amsco RELIANCE 300 Скачать руководство пользователя страница 12

9

Uncrating/Installation Instructions

122993-618

STATUS

STATUS

STATUS

OPERATIONAL TEST

Operational Test

Test procedures included in this section should be performed by a
qualified service technician prior to normal operation of the washer.

1. Open chamber door.  Check that debris screen is positioned in

wash chamber sump.

2. Check that wash chamber is empty and all packing material (tape

and nylon straps) has been removed.

3. Remove manifold connector and inlet filter from bottom of wash

chamber.

4. Unscrew rotary spray holder and lower the rotary spray arm

assembly from top of wash chamber.  Remove rotary spray arm
assembly from chamber.

NOTE:  There is a loose bushing between the rotary spray hub
and top of wash chamber.  When lowering rotary spray arm
assembly, bushing will fall.  Be sure to hold onto bushing while
removing and lowering rotary spray arm assembly.

5. Close chamber door.  Make sure main power switch, located in

upper service compartment (see Figure 3), is in ON position.

6. Press Power-Off/Standby Touch Pad once (see Figure 6).  Verify

that model name temporarily appears on the display screen,

*

RELIANCE

*

*

MODEL 300

*

followed by the first cycle menu screen:

LIGHT

MEDIUM

HEAVY

CYCLE 4

Indicates flashing position.

7.

Press 

Cycle/Start

 touch pad once to select the LIGHT cycle.

Verify name of selected cycle appears on display screen.

PRESS START TO

PROCESS - LIGHT

NOTE:  Pressing Cycle/Start once will select the cycle corre-
sponding to the cycle name flashing on the display screen.

WARNING - PERSONAL INJURY
HAZARD:  When closing chamber
door, use door handle.  Keep fin-
gers/hands away from top and sides
of door to prevent fingers from
being crushed.

Figure 6.  Control Panel

Figure 6.  Control Panel

Figure 6.  Control Panel

Figure 6.  Control Panel

Figure 6.  Control Panel

CHANGE

VALUES

CYCLE STATUS

CYCLE

MENU

SELECT

CYCLE

REVIEW

CYCLE

CYCLE
START

STOP

RESET

EXTEND

CYCLE

POWER OFF/

STANDBY

ALARM

REPLY

SERVICE

MODE

PROGRAM

CURSOR

VALUE

SAVE

VALUES

5

Содержание RELIANCE 300

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды