manualshive.com logo in svg

Amron 8225-HP, Инструкция по эксплуатации

Поделиться
Скачать
Amron 8225-HP Скачать руководство пользователя страница 23

PRE-DIVE PROCEDURES 

19

 

PRE-DIVE TESTING COMMUNICATIONS 

7.4 

1.  Always test the communications between the AMCOMMAND II and divers before each 

dive. Connect the diver’s umbilical to the diver communicator, and the hat/helmet to the 
umbilical. 
 

2.  Turn power to “ON” position. 

 

3.  Set “Tenders Volume” at mid scale. While diver is speaking, adjust to a comfortable level. 

 

4.  Set “Divers Volume” at mid scale. Talk to diver, and adjust until diver can hear tender at a 

comfortable level. If you are using a 2-wire system you must use the “Push To Talk” switch, 
or the push to talk “Hand held Microphone”. 

 

5.  Become familiar with the “Push to Talk” switch by pushing the switch when talking to the 

diver. 

Note:

 If switch is depressed, tender can not hear diver. Diver cannot hear tender if 

tender does not actuate the “Push to Talk” switch. 

 

6.  Check Diver two or the standby diver communication. 

 

CONNECTING DIVER UMBILICAL 

7.5 

 

1.  Remove protective caps and attach diver air supply and diver pneumo hose fittings to 

corresponding outlets. Note: When tightening, place one wrench on outlet fitting and one 
wrench on hose fitting. Tighten hose fitting, making sure not to over tighten. 
 

2.  Blow out divers air supply hose to insure no debris is in the line before connecting to a 

helmet or mask. 

 
Connect the communication cable (surface end) to the two binding posts located on the right side 
of radio. Wires should be well fastened to the binding posts and not touching each other (bare 
wire). We strongly recommend the use of dual banana plugs attached to the top side end of the 
umbilical. This ensures a good connection and reduces the possibility of shorts and/or intermittent 
connections. Attach divers end to helmet or mask. 
 
Test the operation of the system.  

 

LOW PRESSURE SUPPLY 

7.6 

 

Test LP supply with low pressure compressor.  

 

Note:

   Adjust diver air supply pressure at compressor. The AMCOMMAND’s LP supply system 

by-passes the regulator, therefore, can not control air pressure entering system, or the pressure to 
the diver. 

Содержание 8225-HP



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды