manualshive.com logo in svg

Amico ICE 25, Инструкция по установке и эксплуатации

Поделиться
Скачать
Amico ICE 25 Скачать руководство пользователя страница 48

48

     Amico Clinical Solutions Corp.

Troubleshooting

Should problems arise with the use of the Amico Series iCE LED Lights, review the following chart. Find the fault 
and complete the recommended solution. If the fault is not found and or/the solution does not correct the problem 
contact Amico Clinical Solutions Corp.

Fault

Recommended Solution

The emergency red light indicator is “On”

•  Switch “Off” the emergency switch to cancel Emergency By-Pass mode
•  If one or two LED Pods stop working, the fuse may be blown and it may 

need to be replaced by a qualified technician

A button on the main mylar controller has 
stopped functioning

•  The mylar controller may need to be replaced

A button on the wall mylar controller has 
stopped functioning

•  The wall mylar controller may need to be replaced

Lighthead is drifting

•  Tighten up the exposed screws on the yokes or the central axis using a 

3/8" flat head screwdriver.

Glass is dirty

•  Follow “Operation: Cleaning the Amico iCE LED Light”

An LED is not functioning

•  The pod needs to be replaced by a qualified technician

Maintenance: OASYS Spring Arm 

Annual Inspection (to be completed by qualified technicians):

6.  All labels are attached and are legible.

7.  All spring arm components are not deformed.

8.  All moving parts are free from squeaking and are not loose.

9.  Rotational stops are working correctly.

10.  All components are free from collision damage.

11.  Welds are free from cracks.

12.  Load, parallel, brake and vertical adjustments are conducted to ensure the spring arm is performing correctly. 

Refer to section, Installation: Adjustments, pg. 33-37. 

Содержание ICE 25


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды