manualshive.com logo in svg

Amico ICE 25, Инструкция по установке и эксплуатации

Поделиться
Скачать
Amico ICE 25 Скачать руководство пользователя страница 27

     www.amico.com     

27

Installation: Amico iCE LED Light

!

CAUTION - 

Installation and removal for service or inspection must be carried out by a hospital technician or a 

person with similar qualifications who has been trained by Amico Clinical Solutions Corp.

•  Never perform an installation or removal of the LED light alone. Always have a second person to assist with the 

installation or removal. 

•  Always disconnect the spring arm system from the power supply when installing or removing the LED light. 

Failure to do so may result in electric shock. 

•  Always make sure the spring arm is at the highest position when removing the light. Failure to do so will cause 

the spring arm to spring upwards, and may cause serious injury. 

•  The LED light may separate from the spring arm if the key is not properly in place. This may cause serious 

injury. Always make sure that the key is installed properly.

•  Failure to comply with load specifications may cause serious or fatal injuries. Ensure that the LED light load is 

within the specifications.

Installing the Lighthead

Normal System/LCH 

1.  Ensure the unit is disconnected from the power supply, with no possible accidental reconnection.

2.  Apply approved grease to the male end of the lighthead and locking key before installation, to ensure smooth 

movement.

3.  Ensure the safety plug is removed prior to lighthead installation.

PROJECT MANAGER : ___________________

ENGINEERING : __________________________

PRODUCTION : __________________________

55 East Wilmot St.

Richmond Hill, Ontario

L4B 1A4, CANADA

Tel: (905)764-0800

Fax: (905)764-0862

DESCRIPTION:

PART NO:

SHEET:

OF

DRAWING NO: 

PROJECTION

DATE:

DATE:

CHECKED BY: 

RC

DRAWN BY: 

SCALE: 

C

Содержание ICE 25


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды